1. SFATA power breakfast with California State Senator Joel Anderson

    Dear Guest, 

    SFATA are being hosted by California State Senator Joel Anderson this Weds for a "power breakfast". You can bring your input and ideas to him at his El Cajon district office between 9.30 and 10.30. If you're interested and can attend, please visit www.tinyurl.com/SFATApowerbreakfast
     to book a place. Thanks!

    Dismiss Notice

What is your favorite atty?

Discussion in 'Buzz Mods' started by caged, May 2, 2012.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. caged

    caged Ultra Member Verified Member ECF Veteran

    Dec 13, 2010
    Laurel, MD
    I will soon be receiving an IPro and was wondering what everybody was using with their Notcig mod.
     
  2. caged

    caged Ultra Member Verified Member ECF Veteran

    Dec 13, 2010
    Laurel, MD
    Ok, I admit I am lost without Ikenvape. I have no idea what else to try.
     
  3. markfm

    markfm Aussie Pup Wrangler Verified Member ECF Veteran

    Supporting member
    Avidvapor cisco spec 306 (510 connector). Don't forget to also get a 306 dt.
     
  4. caged

    caged Ultra Member Verified Member ECF Veteran

    Dec 13, 2010
    Laurel, MD
    Will they work with Empire Mods drip shields? What ohm do you recommend?
     
  5. six

    six Vaping Master Verified Member ECF Veteran

    Feb 17, 2011
    under the blue sky
    Nope. But you can get a 306 to 510 drip tip adapter at avid vaper. Then they'll take any 510/901 drip tip you prefer.

    As to attys: I am pretty fond of the Cisco Spec 306, but I've really gotten hooked on the hh.357. I personally prefer the 2.0 ohm and I run it around ~4.3 or 4.4v.
     
  6. caged

    caged Ultra Member Verified Member ECF Veteran

    Dec 13, 2010
    Laurel, MD
    I meant drip shield......
     
  7. six

    six Vaping Master Verified Member ECF Veteran

    Feb 17, 2011
    under the blue sky
    Yes. If you have an XL 306 drip tip, drip shields are fine. -- So, if you get Cisco 306's, the best deal is the two 306 atty + drip shield (and choose the XL one) for $19.99 if you don't already have a 306 XL Drip tip.
     
  8. caged

    caged Ultra Member Verified Member ECF Veteran

    Dec 13, 2010
    Laurel, MD
    Thank you. Do you recommend 2.5 or 3 ohm?
     
  9. markfm

    markfm Aussie Pup Wrangler Verified Member ECF Veteran

    Supporting member
    If you are okay with a maximum of 10W at 5.5V, 3 ohm is good, will likely give slightly better run time than 2.5. If you want to be able to go to 12W at 5.5V, use 2.5 ohm.
     
  10. caged

    caged Ultra Member Verified Member ECF Veteran

    Dec 13, 2010
    Laurel, MD
    I have no idea what wattage I want to vape at :confused:
     
  11. markfm

    markfm Aussie Pup Wrangler Verified Member ECF Veteran

    Supporting member
    Pretty typical is a lot of people are actually happy with 8W, around 2.5 ohms/4.5V or 3 ohms/5V. You may nudge it up for some tobaccos, or just to provide a bit more kick during the day.

    I used 3 ohms for months on the original Infinity and Buzz Pro, very happy, When I picked up my tank I switched to 2.5 ohm fusions, still excellent run time and I had the option to go slightly higher on BP on power, though realistically I almost never go above 10W. With my VVPV the 2.5 ohm IO6 atty was a no-brainer to me, again I stay mainly at 8W, 4.5V, will bump up or down slightly during the day.
     
  12. Dougiestyle

    Dougiestyle Ultra Member Verified Member ECF Veteran

    Feb 5, 2011
    Knoxville, TN USA
    I simply love the 2ohm DC atties from CoV. They don't do well with bottomfeeders, but dripping is heaven with them! Haven't burnt one yet and they've been in my arsenal for almost 6 months.
     
  13. caged

    caged Ultra Member Verified Member ECF Veteran

    Dec 13, 2010
    Laurel, MD
    Thanks.

    Are dual coil attys offered from anyone else? CoV has a bad habit of sending you attys at a different resistance than what you ordered and I don't feel like dealing with that possibility.
     
  14. Jason.Stewart

    Jason.Stewart Full Member Verified Member

    Apr 19, 2012
    Downers Grove, IL
    What are you running this on? I am interested in DC atties and looking for something new...
     
  15. hificat101

    hificat101 Super Member Verified Member ECF Veteran

    Nov 18, 2011
    PA
    Hi Caged, I have a Buzz Pro, and I run 2.5 Fusion cartos from Isaac. I never have to turn my B Pro all the way up. I think the 2.5 would give you the most flexibility.

    Are you the same Caged that makes Altoid Tin Mods for Smartvapes? If so, thanks for making more. I've been watching the site for awhile, and was able to order one today. I can't wait to get it.

    If you aren't the same Caged, nevermind.
     
  16. caged

    caged Ultra Member Verified Member ECF Veteran

    Dec 13, 2010
    Laurel, MD
    No. Is there an imposter running around?
     
  17. DaveP

    DaveP PV Master & Musician ECF Veteran

    Supporting member
    May 22, 2010
    Central GA
    My favorite atomizer is a Boge 3.0 ohm carto at 4.2v. 7 to 8 watts satisfies me just fine. If you want to develop a feel for wattage, use the chart below. Find your atomizer resistance and look at the wattage in the chart at various voltages.

    Safe Power and Vaping Chart
     
  18. MarcK73

    MarcK73 Super Member Verified Member ECF Veteran

    Thanks so much for posting that Safe Power Vaping Chart!!! It's a really good quick reference for a beginner!
     
  19. patch

    patch Senior Member Verified Member ECF Veteran

    Mar 25, 2012
    nyc
     
  20. caged

    caged Ultra Member Verified Member ECF Veteran

    Dec 13, 2010
    Laurel, MD
    Well, I grabbed the 306 special in 3 ohm and a cisco 510 @ 2.5 ohm. Figured the 306s would be more delicate so the 3 ohm may be a little stronger.

    Also grabbed a few dual coil SR attys.

    Thanks!
     
Thread Status:
Not open for further replies.

Share This Page