Recent content by littlewierdo

If you have the driver installed on your computer, you can just plug his device in, launch the software, and perform the upgrade. You need to have both the "driver" software and the firmware, which are separate downloads. The settings from your device can be moved to his device, which, if he is...

The mod itself will probably be fine from a fall. Its going to be whatever tank you have that has the issue.

I have no issues with mine. I tend to use one or two devices exclusively, right now, it's the g class. When evolv decides to release a 250c, I'll probably go back to an evolv device. I feel like the g class has so much potential but has not delivered. Firmware updates mainly have fixed bugs and...

You can buy a Windows laptop brand new for $200, I can guarantee you can find a laptop just for the purpose of updating for $40. Can't use it for anything other than web surfing and updating but they are plentiful. Yihi is your favourite company because they responded to an email? Talk about...

This is the charger I use, it's very expensive, about 4x your typical budget charger but it makes batteries last about 20% longer on a full charge provide I use the 0.5 charge rate (this mode takes about 8 hours to charge a 2500 mah battery). It can trickle charge to bring back dead batteries...

Yihi isn't going to replace your batteries. I always take my batteries out if I'm not going to use a device, or, I put it on a charger and let it sit. It's possible a good charger can recover your batteries if it offers a slow charge. If you don't have a slow charge charger, try putting the...

You might need to contact Yihi or the the manufacturer of the mod. I dont know how the 550J chips in devices outside the G-class work. Try downloading the SXI software and firmware from here... SXi-Q Driver/software-YiHi They are different firmware

Follow these instructions to the letter, if you don't, you'll have issues like the one you are describing. 1. Close the sxi software 2. Unplug your device from the pc 3. Disconnect your atomizer from the g class 4. Power down the g class by doing the following: - Press the fire button five...

Check again, this is a repost from yesterday, unless something changed, everything is up to date... https://drive.google.com/open?id=0B4bvEx7Pq_ZhZWJPS2hmM1pMS1E Ive made the firmware and driver available on my google drive account (link above), Yihi makes premium ecig devices but apparently...

Im not sure if there will be a noticeable difference for everyone upgrading to from 6.6 to 6.7, but it is the new firmware they just put up today. I dont have the old changelog to compare to the one for version 6.6. If you are already on 6.6, the install process is significantly faster and only...

Link added above. Note that Yihi put a duplicate update file in their zip. I didnt include both, since they are duplicates...

https://drive.google.com/open?id=0B4bvEx7Pq_ZhZWJPS2hmM1pMS1E Ive made the firmware and driver available on my google drive account (link above), Yihi makes premium ecig devices but apparently cant afford premium web services (Squarespace, Amazon S3, something??) - there are plenty of...

The atty is fine, works fine on other devices. Older firmware seems to have less fluctuation in resistance. As to the base resistance changing after it has been locked, Ive seen it change by 0.01 ohms so it isnt necessarily only when big jumps happen. Im not sure if locking resistance is a...

Not exactly correct, yihi uses a floating resistance. While you can lock the resistance, the mod will change the locked resistance. The material shown on the screen cannot be set to kanthal. In wattage mode, it is not using a tcr value, I get that, but, the material type should still be able to...

I just like that there are really no huge issues to speak of other than a wattage readjustment that is always required when I rewick. Im vaping on an Aromamizer Plus dual coil setup, 40 watts currently, but it never fails, next time I rewick, Ill have to dial it up or down. Also, it seems the...