Search results

  1. gt_1955

    Tensioned Micro Coils. The next step.

    Yes, tension the wire during wrapping the coil around a former; I use a machine screw for this. The advantage is the coil retaining it's geometry indefinitely. Of course, you can't "hot" dry burn the coil else you will stress relieve it (anneal it), losing any advantage. I can't speak for any...
  2. gt_1955

    Tootle Puffers, Part Three! (The Sequel of the Redux)

    And ... I prefer 2.5mm ID over 3mm ID too ;)
  3. gt_1955

    Tootle Puffers, Part Three! (The Sequel of the Redux)

    Some length of wire (of the same gauge) has the same surface area irrespective of what diameter coil you make. Whether that coil has full contact with the wick, and whether that wick can supply an adequate amount of liquid to the coil depends on your choice of wicking material, your skill in...
  4. gt_1955

    Tootle Puffers, Part Three! (The Sequel of the Redux)

    Why? You are using the same length of wire, aren't you?
  5. gt_1955

    Tensioned Micro Coils. The next step.

    The coil retains it's geometry for a lot longer if it's formed under tension ie it doesn't distort as easily as a coil formed without tension.
  6. gt_1955

    Tootle Puffers, Part Three! (The Sequel of the Redux)

  7. gt_1955

    Tootle Puffers, Part Three! (The Sequel of the Redux)

    I'll let @Krisma fill you in in her own time, but she is okay and hubby is slowly recovering ;) Mind, that was last night, haven't heard this morning
  8. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    Probably, but that's not the reason I use them ;) And with rayon as the wick, and with very thin tails extending down the tank can be wicked completely empty. Eggcellent :) Written on 21st Century papyrus
  9. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    I have only used CLR coils in the pico, and they're easy to rebuild ;) Written on 21st Century papyrus
  10. gt_1955

    Tootle Puffers, Part Three! (The Sequel of the Redux)

    I'm not going to go into what I thought "pumps" were ...
  11. gt_1955

    Tootle Puffers, Part Three! (The Sequel of the Redux)

    See ;) Written on 21st Century papyrus
  12. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    Oooooo, squirrel :lol:
  13. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    Filled with a cigar flavoured HEET (heated ethanol extracted tobacco) juice ... vaped @ 12W
  14. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    :D
  15. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    What hot spots? There isn't any with a spaced coil. A thing to note: all the major manufacturers premade coils (blister pack) are spaced (BVCs may be an exception)
  16. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    Sometime back, we were discussing the Pico tank? Mine arrived and I have been using it solely with the CLR adaptor and std CLR 1.0ohm coil. It's okay like that, but you can't use the full capacity of the tank without a lot of tipping to keep the wicks wet. Replaced the std wick (cotton) with...
  17. gt_1955

    Tootle Puffers, Redux (The Sequel)

    He he he ...
  18. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    Ex-smoker?
  19. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    So it wicks ... okay ;)
  20. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    We just don't brag about it ... :lol:
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu