Search results

  1. gt_1955

    Best tobacco for flavor extraction

    Everything in Oz is expensive though ... our minimum wage is $22/hr so that puts it in perspective
  2. gt_1955

    Best tobacco for flavor extraction

    1/4 pound (113g) in Oz would cost in excess of $120 ... an on-line store here is charging $59.99 for 50g
  3. gt_1955

    Tootle Puffers, Redux (The Sequel)

    Because it's battery voltage ...
  4. gt_1955

    Tootle Puffers, Redux (The Sequel)

    Yes she is ;) The eGo ONE only supplies battery voltage similar to a mechanical mod, but is electronically protected and has built-in USB charging not unlike most regulated mods. It can fire down to under 0.5ohms, but I only use 1.0ohm and above on it.
  5. gt_1955

    Tootle Puffers, Redux (The Sequel)

    eGo ONE with Hobbit ;)
  6. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    :lol:
  7. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    I'll give the 2mm a go (and I trim my tails as well). Cheers Roxy :)
  8. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    I love mine too :) Hobbits arrived this morning, smaller deck (obviously) than the Nectar, great surface finish and the logo isn't as bad as I expected ... any build hints? ETA: I was thinking build the same as the Nectar ... 2.5ID contact coil around 1.5ohms, rayon wicking.
  9. gt_1955

    Tootle Puffers, Redux (The Sequel)

    No, hejira's endura
  10. gt_1955

    Tootle Puffers, Redux (The Sequel)

    And perhaps a bit of condensation?
  11. gt_1955

    The Overlooked Tootle Puffer Gear Thread

    Eric's Pretty Mod :lol:
  12. gt_1955

    Tootle Puffers, Redux (The Sequel)

    It's *quite* possible I spelt ecowool/Ekowool incorrectly :D Actually, I checked and it is spelt Ekowool :oops: I bought mine from http://www.vape-atomizer-mesh.com/products/Ekowool.html many moons ago
  13. gt_1955

    Tootle Puffers, Redux (The Sequel)

    :) This is how I set up my Spheroid: 1mm silica approx 60mm long folded in half. Support the silica with a sewing needle (or 18AWG blunt) and wrap your prepared wire firmly around the silica. Space the coils as this reputed provides the best wicking with silica. Once your coil is wound and...
  14. gt_1955

    Tootle Puffers, Redux (The Sequel)

    A couple of us are using ecowool in the Spheroid/Xploras ... same setup as a Prometey (although I'm not sure if looping 3mm is advisable)
  15. gt_1955

    Tootle Puffers, Redux (The Sequel)

    Silica or ecowool is the go ;)
  16. gt_1955

    Tootle Puffers, Redux (The Sequel)

    By inserting tubes into the air holes, it raises the air outlets above the deck allowing some liquid to pool on the deck without flowing back down the air holes.
  17. gt_1955

    Tootle Puffers, Redux (The Sequel)

    Jack Daniel's ??
  18. gt_1955

    Questions about extractions

    I agree, you do extract *some* WTA, but once mixed to your eLiquid you will vape, it will be minor (depending on your recipe). I'm currently using 1% heated ethanol extracted tobacco (Str8vision), 2% cold macerated (>90 days) extracted tobacco (various authors), and 20% WTA extracted tobacco...
  19. gt_1955

    Questions about extractions

    No problem mate ;)
  20. gt_1955

    Questions about extractions

    I would just like to point out that NET (flavour) extraction is not a WTA (alkloid) extraction (that uses a whole different process).
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu