Search results
-
Eleaf iStick "pico"
I only use the green one with a mech mod. It won't even fit inside the pico. Here is a link where I ordered it: https://www.fasttech.com/p/1345500 -
Favorite tobacco flavoring discussion - Tobacco flavoring discussion only
Floral? Which brand of 7Leaves - FA or INW? What %, and how long a steep? This one takes quite a while to develop. I mix it at 2%, and get no floral flavor after 4 weeks of steeping. Heat does not help with this one !! Anyway if you still do not like it at the end, I will take all you got :)- Exchaner
- Post #2,727
- Forum: DIY E-Liquid
-
Eleaf iStick "pico"
This one came with a wrapper, but it won't fit inside the pico. It only goes part of the way. Perhaps because it is a button top? I don't think so ... -
Eleaf iStick "pico"
By plastic wrapper I mean the transparent material similar to Saran Wrap that should be encasing the battery itself. It's actually a thicker and harder material than Saran Wrap. I always thought that plastic should be removed before use. Is it not? As you can tell, I am a newbee ... Here is a... -
Attack of the (Kayfun Mini V3) Clones!
With rayon the tails are supposed to be as thin as possible. The problem is, no juice is reaching the tails... -
Attack of the (Kayfun Mini V3) Clones!
Hi everyone, I followed all your suggestions, and I am still getting dry hits. My juice is 75%vg, 4% distilled water and 21% pg. I am posting a picture of my wick just to show that I am using a minimum amount of rayon with the tails trimmed down to a minimum. Juice holes are all clear. I do... -
Attack of the (Kayfun Mini V3) Clones!
Hey guys, I am having a unique problem with dry hits. I am wicked properly, the juice holes are completely open, and the juice flow control turned 2 1/4 rounds. My juice is 75% VG. Sometimes I see bubbles coming up, sometimes not. They start coming up again after I draw some hefty prime puffs... -
Attack of the (Kayfun Mini V3) Clones!
See picture on post 1409 a couple of pages back. You need to hold the bridge steady with a paper clip and tighten the hex nut at the bottom. -
Favorite tobacco flavoring discussion - Tobacco flavoring discussion only
Thank you for this suggestion. I tried blackberry by itself, without the peach, and it goes very well with my favorite tobacco. Just 4% did the job. I will try adding some peach to see what happens.- Exchaner
- Post #2,707
- Forum: DIY E-Liquid
-
Eleaf iStick "pico"
Just comparing the HG2 on the pico vs a different battery on a mech. Watts are similar. I am thinking the pico drains some juice because of the circuitry. -
Eleaf iStick "pico"
Yes, without a plastic wrapper. I wrote to VapeNW, and they said that is normal. Doesn't make sense since the box specifically states do not use battery if plastic wrapper is damaged. In my particular case, it was not damaged - just missing - as if they had sent a used one. -
Attack of the (Kayfun Mini V3) Clones!
Thanks, you solved my problem. I was putting the o-ring on the juice channel; something you would expect from a newbee ... -
Eleaf iStick "pico"
I notice my Hg2 lasts slightly less on the Pico than other mods. Also noticed the battery came without a plastic wrapper mentioned on the box. Is that normal? -
Eleaf iStick "pico"
That particular ego is actually shorter than the pico - much easier to hide given its thin profile. It's only 1100 mah - enough for a day of vaping for me. As for the tank, there might be shorter tanks available than the Kayfun mini shown in the pic. -
Eleaf iStick "pico"
Good thing you mentioned "relative". Speaking of the ego, this setup is my all time favorite; stealth as you can make it - or close. I only vape at 15 watts though ... .... -
Eleaf iStick "pico"
Hey guys, I love my Pico, but what is so "stealth" about clinching something in your fist and sticking it to your mouth :yawn: -
Attack of the (Kayfun Mini V3) Clones!
I still have the old one, but mixed it up with the others. Now I have to figure out which one is which... How many o-rings are we supposed to have for the bottom of the deck? -
Attack of the (Kayfun Mini V3) Clones!
Hi everyone, HELP !! I changed the o-ring on the bottom of the deck because the juice flow control was hard to turn, but now it is turning at the slightest touch. In addition, I am getting dry hits no matter how many times I turn - bubbles are not coming up. I may be using the wrong o-rings... -
Attack of the (Kayfun Mini V3) Clones!
The ego one is rated to handle anything from .5 to 1 ohm, but I am using it with a 1.2 ohm. So far no apparent problem. My coil is 30 GA Kanthal, 2.5mm ID (4/5 wrap). I understand it is not a good idea to use high resistance on a mech though. 1.2 ohm is considered border-line high. I vape around... -
Attack of the (Kayfun Mini V3) Clones!
You guys can have your fancy mods. I am perfectly happy with this setup. It goes everywhere with me.