Search results

  1. nj1001

    Check out my Nano "dragon" Coil build

    So there are obviously numerous variations with this and I'm sure they're all sick. What I'm wondering is if there's an improvement if the coil's opening is aligned to the air intake as opposed to just having the coil perpendicular to the air hole. Looks like both work well, but iTEO, your...
  2. nj1001

    Alexander Mundy's Magic Twisted Ribbon

    Ok, I apologize in advance because I recently found this thread & am excited to give it a try and am looking at getting all of the necessary materials ASAP but I admit I have not yet had the chance to read the entire thread yet so I'm sorry if I'm asking something already covered. I am...
  3. nj1001

    Introducing Futura - The Modular DNA 20 APV by NexgenVapor[ISSUE]

    Titanium finish here! I did so for 2 reasons: Hope it'll look nice with my atties & quicker to ship out to me.
  4. nj1001

    Check out my Nano "dragon" Coil build

    @ Elgato... Are you sure you've positioned the coil close to the airhole? If not you'll get intense TH will significantly less vapor. Like others mentioned, even though 42 pages deep and counting, this thread if read through should explain everything you need to know with one of the first...
  5. nj1001

    Check out my Nano "dragon" Coil build

    The only problem I have with the open nano 'dragon' style so far is that I keep setting my smoke alarm off.
  6. nj1001

    Anything new thats not out yet but soon?

    Wizards apprentice evolved is up on his site right now!!! Cost is 250 euro which is about $340. They're going to be shipped by November 2nd I think is what I read. Doubt these will be available for long.
  7. nj1001

    Check out my Nano "dragon" Coil build

    Then juiced well And making sure the air hole lines up perfectly with the open coil. Flave cloud maker.
  8. nj1001

    Check out my Nano "dragon" Coil build

    28 gauge kanthal wrapped into a 1.1 ohm nano coil on an Origen. I off set it so the hole pointed up a bit and to the side of the center pin. Started with loose cotton under the nano coil then flipped both ends over the top and to the wells on the opposite sides. Making sure both ends of...
  9. nj1001

    Battery Charging & Charger

    I have a pila & an xstar vp1. I think I prefer the xstar because of the screen. I got em both after research because they were highly rated as being some of the best/highest rated. Never had any problems with either.
  10. nj1001

    Introducing Futura - The Modular DNA 20 APV by NexgenVapor[ISSUE]

    I'm not worried. Less posting here means more working on the mod release. I am curious about the rocker switch. Think its like a wizard style electro static sensor or something?
  11. nj1001

    Magnets vs. Springs

    Eh... depends on the device and the spring maybe? I know with the nemesis the magnets are silver plated but I don't know if it really matters how conductive they are because its the pin making contact with the battery and not the magnet. My understanding is that its a matter of touch...
  12. nj1001

    Anything new thats not out yet but soon?

    I think you should have specified what price range you were looking for in the initial post. It would certainly narrow down recommendations folks would suggest. However, since nothing much cheap interests me at the moment I will tell you about some of the things I have seen/heard about. I am...
  13. nj1001

    Having a problem burning out cartos FAST

    Fill your cartos from the bottom by saving the little rubber condom that they are packed with- the one that doesn't have an inner nipple, pour juice into that and slowly and gently press the atty screw side down, into it nice & slow. That will ensure you're getting juice to the bottom where the...
  14. nj1001

    Are these batteries safe

    What device are you using them with? A regulated provari or DNA20 mod or mech? What type of atty do you run? Are you into sub-ohm'ing? Hands down the most safe are red AW IMRs and orange MNKEs. Its all I use and all I'd recommend. Efest (sp?) are also known to be good but I've never...
  15. nj1001

    A Vape to the past

    Eh... I OD'd myself on cartos for years. I'm glad vaping has evolved. I've never gotten flavor or vapor from a carto that comes close to a RDA, kalifun, etc. I can confidently say that I will never touch one again in my life. I did step back from years of cartos to a regular ol' 510 atty for...
  16. nj1001

    What are your preffered Sweet Juice? any desciptions?

    #1 - Dragon Ch'i & Cran Ch'i by Halycon (my ADV) #2 - Pink Starburst & OOber Goober by eLiqCube #3 - Grant's Vanilla Custard #4 - Peach & Pear - both all natural by Highbrow Vapor #5 - Unicorn Blood
  17. nj1001

    All Day Vape Favorites

    Halycon's - Cran Ch'i & Dragon Ch'i I rotate between those two all day everyday, have been for about a month and don't foresee changing anytime soon. Also, FYI, the Ch'i is short for lychee as opposed to the tea. They're fruity and refreshing & not too overbearing or overly strong in flavor...
  18. nj1001

    Which Vendor Next?

    Also, I should say, I was a fan of pluid and unicorn blood but I find they're such excessively strong flavors that it has been my experience, more so with pluid, that it almost requires a dedicated atty because anything you try to vape afterwards wont taste as it should. Unicorn blood wont...
  19. nj1001

    Which Vendor Next?

    My absolute #1 favorite all day vape for the last few weeks has been and will likely remain for a long time two juices which I rotate between: Cran Ch'i & Dragon Ch'i from Halcyon. First off let me say the Ch'i is short for lychee as in lychee berry and not the tea. The cran is phenomenal...
  20. nj1001

    Check out my Nano "dragon" Coil build

    anybody try this on an Origen dripper? I'd LOVE to see if its possible
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu