Search results

  1. IMAG0802

    IMAG0802

    Carbon Fiber Hydrodip case body. Fire button side.
    • jblack741
    • Media item
    • Comments: 0
    • Album: 26650Mod
  2. IMAG0786

    IMAG0786

    Initial painting.
    • jblack741
    • Media item
    • Comments: 0
    • Album: 26650Mod
  3. IMAG0780

    IMAG0780

    Drill/cut, sand and primer.
    • jblack741
    • Media item
    • Comments: 0
    • Album: 26650Mod
  4. IMAG0720

    IMAG0720

    Initial markup and parts layout.
    • jblack741
    • Media item
    • Comments: 1
    • Album: 26650Mod
  5. 26650Mod

    26650Mod

    Build Process
  6. jblack741

    Vanilla Rum Custard

    ***Nic is 100% PG /48mg Strength*** **Target 6mg** **30ml Bottle** ---------------------------------------- Sweeten to taste! Enjoy! *Notes:* I use a mini bartender blender to mix till creamy white, let it clear and repeat. This is done while sitting in a cup of water heated to about 80deg...
  7. jblack741

    Best tool for mixing up your e liquid IMO.

    I use a microwave safe prep cup 2oz size, fill half full with water and heat for 1 minute. Then take my mix which is done in a 50ml beaker set it in the hot prep cup and froth from there. Let the bubbles clear and repeat. I typically froth until the entire mix is creamy,let it clear then bottle it.
  8. jblack741

    Should I keep these P-Channel Fets

    Had a large order from Mouser and ordered N-Channel fets (3034) and also received 2 of the following: MOSFET 30V 6.2mohm @ 4.5V Id - Continuous Drain Current: 18 A Vds - Drain-Source Breakdown Voltage: - 20 V Rds On - Drain-Source...
  9. jblack741

    18350 Battery Holders...

    Dual 18350 - Dual 18350 Battery Tray | Modz By Nasy Dual 18650 - Dual 18650 Battery Tray V2 | Modz By Nasy Dual 26650 - Dual 26650 Battery Tray | Modz By Nasy I've used the 26650 both dual and single. I like the clearance they have and the quality is outstanding. 3d printed for the 1590g...
  10. jblack741

    First Time Building a DNA 25 and need some help

    I've done 2 DNA 30's so far and I would recommend using flux, tinning all of your wires first and make sure you have a good soldering iron so you don't sit on the board to long with the heat. Tinning your wires first will help the the solder flow over the pads, giving you a nice clean finish.
  11. jblack741

    Building a "hana" style mod with the fasttech enclosure: looking for tips, tricks, and suggestions

    I just drilled out the hole slightly larger than the original hole to expose the bare metal, tinned my ground wire, snipped a small piece of solder into the hole and soldered the wire directly into the hole. I then covered the connection with liquid electrical tape.
  12. jblack741

    hana dna40 clone help

    Unless you're going to rework the board... toss it!
  13. jblack741

    Better undesrstanding of MOSFETS

    This is what I use jonny. Mosfet
  14. jblack741

    1590g Mosfet box, need help, tried everything i know of...

    I only bought 1 fet from ebay and it didn't work for me. I thought it was something I had done wrong, like burn it up or short it out but I never got it to fire and I was using the exact schematic that's on FindMyVapes for an unregulated mode. I bought from mouser and soldered it into the...
  15. jblack741

    Looking for good circuit diagram for reverse polarity protection to use with a DNA25/30/40 chip

    Thanks Visus, great info!
  16. jblack741

    Looking for good circuit diagram for reverse polarity protection to use with a DNA25/30/40 chip

    Thanks but none of the documentation state this. I know the 30 does not, I've burned one up sadly enough. I've submitted an email to Evolv for clarification so I don't make any assumptions. Thanks again.
  17. jblack741

    Looking for good circuit diagram for reverse polarity protection to use with a DNA25/30/40 chip

    I'm want to build in reverse polarity protection for use with Evolv DNA series chips because they don't have it built in. I'm building both a dual parallel 18650 and 26650 boxes and plan to use a DNA 40 for the 26650 box and a DNA25 for the 18650 box. Thanks in advance. jb
  18. jblack741

    First Attempt at DYI

    On your fist one, I'd drop one of the butter entries and the smooth. The second one, may want to drop the butter and add sweetner. I have not tried Rice Crispy flavoring so I can't really say. For the third one, the brown sugar is going to take a week before you reaches a point where you can...
  19. jblack741

    not getting enough nic? fresh quiter of newport 100s need help

    That's an odd calculation... I've never heard that before and to me it doesn't sound right. Based on your calculation I'm at 246 20.5w x12 and I don't have a headache nor is it too light. Everybody's different and their absorption levels are different... please explain how you came up with this.
  20. jblack741

    Just registered

    Hey from across the pond... Vape on!
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu