Search results

  1. AtmizrOpin

    Joyetech CUBOID 200 *NEW*

    LOL, this thread died with a quickness. well, i am a "lucky" recipient of one these mods. it was given to me for nothing, so i can't complain. this mod does have one redeeming quality that many may not know. you can use the Arctic Fox firmware with NFE Toolbox for a fully customizable device...
  2. AtmizrOpin

    Closed/Sold (US) - Selling - Priced to move Spring cleaning sale.

    PM sent for VF DNA 40
  3. AtmizrOpin

    Ruleaux DNA 200 issues

    i'm going to bet, that if you look in EScribe's Device Monitor, you will see incorrect cell voltages being read for all 3 cells. if a new set of cells does not fix the problem, most likely the board is bad. one way to check if the analog front end (cell monitoring/balancing IC) went out is to...
  4. AtmizrOpin

    Lost Vape DNA 60 Mods

    i was able to cram it into a VS RDNA 40. my post starts at #86 of the page.......... DNA 60 - Evolv DNA Forum
  5. AtmizrOpin

    Lost Vape DNA 60 Mods

    i like the petite, smaller the better. the 60 is a nice board. i've been using one for a few months now. it doesn't get a whole lot of use though. 60w is just about 10-15 watts of where i normally vape. it's a great board for single coil jobs or high ohm, low mass dual coil jobs (9v limit)...
  6. AtmizrOpin

    What temperature do you vape on?

    480F - 550F DNA I like a warm - midly hot vape.
  7. AtmizrOpin

    Any thoughs about the Segelei Fushai 213 Plus?

    i bought the fuchai 213 plus (color screen). the only reason i bought it was for the color screen, only $40 from ecig.com (biggest deciding factor) and it's small size. here's what i can tell you, if you want a good TC mod, look elsewhere. it does TC just fine but i do not like the delay it has...
  8. AtmizrOpin

    Lost Vape Therion 166 (DNA250)

    Correct, "is not enough". Ditto what Steve said.
  9. AtmizrOpin

    Unusual problem with my Therion DNA75

    sounds like the base resistance is changing when you change the batteries. atty is still warm when you change the batteries so the board reads an incorrect base resistance when the new batts are installed, resulting in a burnt hit/wick. the DNA 75 will not remember the resistance is the battery...
  10. AtmizrOpin

    Vaporshark DNA250

    i'm going to email them about the 250 upgrade. only catch is i want my old 200 board back when they dump in the new 250 board. it'd be great to have as a spare, just in case.
  11. AtmizrOpin

    Sanyo 20700B 4000mAh 20700 Bench Test Results...a peek at the future?

    as soon as i saw this email in my inbox, i wanted to buy two of each even tho i have no mod that will fit (without modification) nor a 20700 sized sled, LOL. i'm sure i can figure something out........
  12. AtmizrOpin

    Evolv DNA 75

    what are your individual cell voltages? you might just need a new lipo, not a replacement board. the Fullymax 900mah 3S 11.1v might be a direct drop in replacement. evolv sells them as do a few other online hobby stores. you can still send it to evolv. they'll charge you for the lipo...
  13. AtmizrOpin

    Evolv DNA 75

    EScribe comes in handy for diagnosing just about anything. charging would not be affected by the board screws. there can be quite a few reasons why your charging current is so low. this is where device monitor comes in handy. could be imbalanced cells, too low of an individual cell voltage, an...
  14. AtmizrOpin

    Evolv DNA 75

    volcano cheaps out on the 510 ground for their 200 and the 75 mods. the 3 board mounting/grounding screws get loose and dirty over time requiring cleaning and re-torquing down. same thing with the silo/erm (whatever you wanna call it), the hana v200, hotcig dx200 and the araia solara dna 200...
  15. AtmizrOpin

    Problem with Therion and TC, weak vape

    you never stated what wire material you are using for TC. I'm going to assume SS 316. Just know, kanthal/nichrome will not work in TC mode. I've noticed with SS i have to turn my set temp to 500F + to get the vape i'm looking for. Spaced coils are ALWAYS best for TC, eliminates hot spots/shorts.
  16. AtmizrOpin

    S-Body Macro DNA75

    If you have higher than a .5 resistance (around thereabouts), you won't get the full 75 watts on the DNA 75.
  17. AtmizrOpin

    S-Body Macro DNA75

    just know the DNA 60 is NOT a direct drop replacement for all DNA 40 devices, especially ones that utilize the DNA 40's on board buttons and and just enough room for the board. the DNA 60 uses completely different (taller) up/down buttons, also uses the DNA 75's fire button and the 2 inductors...
  18. AtmizrOpin

    S-Body Macro DNA75

    the DNA 60 board isn't the same shape as the 75. it's more like the DNA 40 footprint. this is the DNA 60
  19. AtmizrOpin

    S-Body Macro DNA75

    anybody feel like taking the screws out, removing the cover plate and snapping a few pics of the internals?? got a few ideas, just wanna see if it's doable.
  20. AtmizrOpin

    TC Issues With 316L

    i agree. i noticed with some build/atty's, if i let the board refine my resistance (take a few puffs, set the device down for 15-30 min) then lock in that refined resistance, it's a more stable consistent vape. otherwise, especially with this weather, my res will creep up/down a small amount...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu