Search results
-
Unleash the last of the woodvils please!!
The ones that are available have a "BUY NOW" button on the first page Could be a browser issue for you -
Need a fix for a button
The o-ring will work and stay in the button cap 1/8 ID X 1/4 OD X 1/16 CS fits perfectly -
Need a fix for a button
One thickness of dental floss will keep the button cover on good Place the button in the locked position Cut a small piece of floss about the width of the button then position it so that only one thickness of floss overlaps the button in one place, then push the button cover on -
Need a fix for a button
I've put an o-ring in the button cover before I install it Gives you a little extra throw(the thickness of the o-ring) Sounds like you need about 1/16" thick 1/8 ID X 1/4 OD X 1/16 CS fits perfectly And it will stay in the button cap when its off the REO -
Where's rob??
If your looking for Rob You can find him right here -
Question on 2015 Woodvil Button
Some 2015 Woodvil buttons come apart easier than others Mine was easy to remove One thickness of dental floss will keep the button cover on good Place the button in the locked position Cut a small piece of floss about the width of the button then position it so that only one thickness of floss... -
Sub ohm coils in a Cyclone
I would trim that wire nub flush with the positive post It looks close to shorting -
How to take apart cyclone afc cap???
The Cyclops AFC is only hard to disassemble the first time you take it apart After that it gets easy Tapping the right size wooden rod inside the cap while holding tightly and pushing down on the outside of cap Is the way to do it -
Closed/Sold (US) - Sell or Trade - Titanium mods Ukraine eagle
Very Tempting But I'm Finally PVed Out BUMP- tobarger
- Post #17
- Forum: Member Classifieds and Swaps
-
Sometimes the truth is more ridiculous than anything you can possibly make up
Sometimes the truth is more ridiculous than anything you can possibly make up- tobarger
- Profile post
-
Anyone removed their hammertone finish?
You can really just BLOW the paint off with an air compressor? There has to be more to it than that, maybe your using the compressor with a sandblaster And HammerTone is about the most durable paint Rob uses I have a secondhand HammerTone VV Grand and it looks like the day it was born -
Chalice III
Chalice3 version2 - Shorter driptip and a little more air flow -
Patina mod and door progress
Rob Do the same with an LP Copper-Vein Grand and I'll take it -
ReadyXWick - Round 2
MacTechVpr I've been looking at Pin Vises all day on Amazon and eBay Can you Please supply a link to the best Pin Vise you have found for tension winding coils? I was looking for one with a non tapered section near the jaws for resting on the edge of the spool But I couldn't come up with... -
Coil Master ?
If you find anything good on Earth that sells online let us know in this thread -
Coil Master ?
I have two Coil-Masters(V2 and V3) and a Gizmo The Coil-Master has more usable posts The Gizmo only has one usable rod for me, the 1.5mm(1/16") I wish it had a 2.5mm rod for 3mm READYxWICK because I like the tensioned coils it produces I don't think the Coil-Master applies much tension at all... -
Closed/Sold (US) - Selling - Hawaiian Koa Sumpin by pdib
Beautiful Woody- tobarger
- Post #9
- Forum: Member Classifieds and Swaps
-
adjustable 510 on new woodvil
The grub screw is the only adjustment in the new 510 connector -
Wife burning wicks
Are you sure that 3mm READYxWICK slides right into a 3/32" coil? 3/32" = 2.38125mm 3mm READYxWICK = 2.7mm RBA Suppies recommends 7/64"(2.78mm)snug to 1/8"(3.17mm)loose for 3mm READYxWICK -
Reo/ bottom fed advice.
Oh... Most people build the coil on the same side of the posts as the squonk hole