Search results
-
306 atty question
To get about 8 watts from any atomizer R + 2 = V V^2 / R = W Been using it for years !!! Works Every Time !!! -
306 atty question
They are not dangerous to use, you just need a regulated mod to get the voltage well over 4 volts or wattage over 8 watts My VV REO Grand and ProVaris have no problem doing 2.6 ohms A good general rule is if you add 2 to the reistance and set the voltage for that value you will be at or... -
306 atty question
I think RFs suggestion is right on for an unregulated mechanical mod "If you prefer sweet juices, I would stick to 1.8-2.0. If you're more into tobacco flavors, then the 1.5 may be the one for you" 2.6ohm resistance would be more for a regulated VV or VW mod -
Woodvils- Admit It Here.
I think I'll just let the collectors buy them all again Then just leisurely watch the classies for them to start showing up And only if they are in new condition will I consider buying one That will keep me busier for longer than trying snag one in the maybe 5 minutes before the site crashes... -
-
Now that I HAVE to have one...
Correct RM4, 5 and 6 are AFC atomizers -
Now that I HAVE to have one...
For an LP Grand you should have these spare o-rings 6ml Bottle cap Under Atomizer - 1mmCSx10mmID Under Atomizer - 1.5mmCSx10mmID -
Now that I HAVE to have one...
REOsMods.com O-Rings: 3ml Bottle cap 6ml Bottle cap Under Atomizer - 1mmCSx10mmID Under Atomizer - 1.5mmCSx10mmID -
O-Ring RM4
The correct size is 15mm OD x 1.5mm CS The 10mm ID x 1.5mm CS o-rings that are sold by REOsMods.com should also work -
What drill size for Squonk bottle cap?
Tubing OD=3/16"=0.1875" Drill 11/64"=0.171875" -
Has anyone here ever converted a non-bottom fed Cyclone to squonk?
Thanks for the pictures of the 510 pin custom-classic First time I've seen it removed First time I've heard of drilling it from the top, makes alot of sense to do it that way Saved it for future reference -
-
router drip tip
I think someone compared the Router Bit on a Divo to a pregnant cow Maybe on the So what if it looks like crap thread Just tried the Router Bit on a MCV Atomic If the RM4 is a 1 to 1 clone it will work beautifully The Router Bit ends right at the beveled edge of the MCV Atomic -
Stripped spring screw
I'm thinking a spare spring screw will be in my next order Along with a couple springs Get ready Rob... I don't order all the time But when I do I prefer REOsMods.com -
router drip tip
Is there a chance that the orders only make it to the post office once a week I'm guessing Tuesday That seems to be the only way it makes sense to me I know I'll get it, but 9 or 10 days seems to be typical -
oh cant wait
That setup will work, nice job I just got a flashback to when I got my first REO You had to be lucky to get one When they became available they sold out almost immediately That was only about 4 years ago -
router drip tip
Believe it I'm using a Cyclone now and measured everything with a digital caliper The LokiLab .45 Stubby(OD = 11.9mm) fits the Cyclone(OD = 13.1mm) real nice Router Bit ID = 5.3mm OD = 15.7mm .45 Stubby ID = 5.5mm OD = 11.9mm Try it you'll like it I don't have a Divo but its top looks even... -
So what if it looks funny...
The .45 Stubby(OD = 11.9mm) fits the Cyclone(OD = 13.1mm) real nice Router Bit ID = 5.3mm OD = 15.7mm .45 Stubby ID = 5.5mm OD = 11.9mm Try it you'll like it -
Cisco Atomizers keep dying
Once you switch to rebuildables you can carry a disposable atty in case of emergency Thats about all they are good for nowadays I have a bunch of new disposable 510 & 306 attys that I will probably never use -
router drip tip
Got my Router Bit & .45 Stubby yesterday They are very nice The Router Bit is no good (OD too big) on a Cyclone The .45 Stubby works good (OD 1mm smaller) on a Cyclone