Search results

  1. R

    smok TCT

    mike vapes shows it on you tube
  2. R

    new design idea for attys?

    All this info is over my head but in case it is useful to designers here is a link about blade less wind turbine. Wind Power Without The Mills - Forbes Claims to use less moving parts and reduce noise. I have not used a fan atty but heard people complain about the whistle and noise.
  3. R

    Thank you for all your help!

    Thank you for all your help!
    • Rumi
    • Profile post
  4. R

    Old Coils, rust, bad flavor, easier to gunk?

    Nuppin build looked ok till I held the unused wire next to it
  5. R

    Old Coils, rust, bad flavor, easier to gunk?

    The Odin build is trash after 1 day rusty.
  6. R

    Old Coils, rust, bad flavor, easier to gunk?

    Looks black to me gonna clean now. Went through about 15 ml of juic on the flask and about 10 ml on the peko.
  7. R

    Old Coils, rust, bad flavor, easier to gunk?

  8. R

    Atomizer short?

    Ok that didn't make sense to me dumb it down please. I tried this test with no coil on suspect atty and one that works fine and meter reads o.l at rest then numbers jump crazy when leads are applied to threads and pin. Don't I need a coil to complete the circuit?
  9. R

    Atomizer short?

    the insulation is my suspicion, so I should test it negative on thread and positive on post without a coil and read "00" meaning no short or jumping numbers would = short?
  10. R

    Atomizer short?

    i could only find 1 video that showed an atomizer short which said to hold black lead of multimeter to the threads then push with the red lead on the bottom of the positive post and if your numbers jump you have a short. So I recoiled my patriot clone rda and tested with the meter before...
  11. R

    Old Coils, rust, bad flavor, easier to gunk?

    I appreciate all help since my first assumption is that I am doing something incorrectly. I did not do any modifications to the mod. It was bought as a sqounker/ bottom feeder and I paid that price because it was the only regulated sqounker available in the past 3 months, pre made and made in...
  12. R

    Old Coils, rust, bad flavor, easier to gunk?

  13. R

    Vapers Choice Cotton Wick Anyone?

    Thanks I'll try again. Cotton I build with a slight dragging feeling through the coil meaning some resistance but not enough to yank my mod. The rayon video I watched said to use less density than cotton so I will try more. Also I was told that for sqounkers I don't need to "choke" the coil...
  14. R

    Printed Mechanical Bottom Feeder Mod

    Thanks sending a request for the large button! :thumb:
  15. R

    Benefits of using wire mesh?

    I'm interested too. Can only find videos of the genesis style tanks and one two post bottom feed atty in English. I want to know if it can be built horizontal on a three post atty or at least one bigger than the graal. I'm trying to find a solution to building coils every 2 days cause of gunky...
  16. R

    Old Coils, rust, bad flavor, easier to gunk?

    I'm in the same predicament as you phone guy but even faster. I abandoned tanks cause I would get the burn taste on the first or second day and by the third I began wheezing and coughing and phlem build up. So a clean coil helps prevent those problems but I'm getting tired of coiling so often...
  17. R

    Vapers Choice Cotton Wick Anyone?

    Found the texture a little more difficult to work with but I think that just takes practice. I did not really notice a big flavor difference compared to cotton on the fresh build. On the 2nd day which is usually when my Japanese cotton tastes like burnt gunk the vcc tasted like wet cotton, made...
  18. R

    Printed Mechanical Bottom Feeder Mod

    Unfortunately I can't even glue and screw apparently lol. That's why I chose to purchase a pre built one. I was hoping if I could fix it I would try building one from scratch. The design is so genius, comfortable, light, and I love the non metal option. The nut on the button keeps coming unglued...
  19. R

    Printed Mechanical Bottom Feeder Mod

    . Is the spring supposed to rest on the brass nut that is glued to the fire button? My spring is wide and rests around the nut against the plastic fire button. Is this why no matter how much I turn that button either way it will not raise, lower or lock the contact screw? Or am I...
  20. R

    Printed Mechanical Bottom Feeder Mod

    Yes movement of the contact does not happen when turning the button. I believe it is the low button version, the metal contact beneath the frame barely moves when button is fully pressed and it looks tilted, one side lower than the other but that could be uneven sanding of the plastic right...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu