Search results

  1. Filthy-Beast

    Resin mods

    Mornings are not bad at all I've taught her to whisper good morning. However if we stay up late and don't turn off her light and cover her for bed on time she let's you know. If you're in the same room as her you'll wonder if your ears are bleeding.
  2. Filthy-Beast

    Got my first squonker yesterday

    Congrats on great looking setup and Welcome to Reoville
  3. Filthy-Beast

    REOs not performing well?

    Glad you got it!
  4. Filthy-Beast

    Resin mods

    Here you go Dennis is this better? With a beak that can deliver up to 750 PSI, she could shred a resin in no time.
  5. Filthy-Beast

    REOs not performing well?

    Not sure if I saw it answered. Yes you can use a tooth brush and soapy water on your metal Reo, I do all the time. If it loosens up a bit keep moving it around in the soapy water to help get all the gunk out. If you need to pull the delrin cover, it's not bad at all. PM and we can jump on...
  6. Filthy-Beast

    REOs not performing well?

    Sounds like it might just be junked up a lot. Try soaking in a nice hot bath for a while. If that doesn't loosen it then we'll need to pull out the delrin cover and take a look under the hood.
  7. Filthy-Beast

    Title edited [CLOSED] Unregistered

    Glad you're ok and very sorry to hear of the lose of your best friend. Hope all goes well with surgery and that you enjoy Germany.
  8. Filthy-Beast

    REOs not performing well?

    You can try your hand at making one from a brass feeler gauge. Trickiest part is getting the center pin nipple nut off without breaking it. I used a .012 gauge and cut it with kitchen scissors.
  9. Filthy-Beast

    Resin mods

    I love African Greys. We were worried the stress of three kids and 3 dogs would be too much for a grey so we got a Blue and Gold macaw instead.
  10. Filthy-Beast

    Question about arcing

    The pliers was actually a good idea. Make sure the nut nipple is good and tight. Also make sure it has not pinched any of the silicone sheath that is on the firing pin. You want a good tight connection that sandwiches the firing pin in place. Even slightly loose leads to an increase in arcing...
  11. Filthy-Beast

    Collapsed my first spring today.

    You want it about where the RM2 in center has its pin. Also pocket lint with a little foil from gum or mints has been known to cause a short.
  12. Filthy-Beast

    Time to Introduce Myself

    Great to see you over here, Welcome to Reoville.
  13. Filthy-Beast

    Question about arcing

    Are you a slow press on the fire button. The longer the contact is close to connecting but not quite there the more arcing you'll get. Also don't be shy with deoxit. Also is this with the new gold contacts in the Reo or the older silver contacts?
  14. Filthy-Beast

    I'm thinkin' maybe we should try this again? . . . . and you kids should behave yourselves

  15. Filthy-Beast

    Just wanted to share

    Congrats and Welcome to Reoville!
  16. Filthy-Beast

    Nuppin'

    Depending on how low the drip tip goes there is still a lot of room above your coil
  17. Filthy-Beast

    Suppliez

    RM2 came first and was cut skinner on the bottom to fit in the drip well of a regular REO. LP RM2 came later and is not cut down. TWO LP RM2 on the left, regular RM2 on the right.
  18. Filthy-Beast

    Suppliez

    Yes a regular atty will work on an LP, it just doesn't have a drip well so to speak. LP on left, regular on right
  19. Filthy-Beast

    Nuppin'

    Hard to tell from that angle but looks like it needs to go higher, The Nuppin air holes are pretty high up. bottom of my coils are very near the top of the center post.
  20. Filthy-Beast

    The Nicoticket Approved Delivery Device Advice Thread

    Roll with it an enjoy, the Nuppin hits harder than most, that's why you still love the vape. Remember the down leg adds to the total resistance so even though your wraps might be equal you total length from capture screw to capture screw might be longer.
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu