Search results

  1. drunkenbatman

    RDA Kanger Subtank Mini... RDA and OCC questions?

    No! The OCC coils are cotton wrapped in kanthal, you'll just ignite the cotton. The tools are for rebuilding the RTA coils, which you can dry-burn after removing the wicking. You'd generally do that when the wicking and coils are all gunked up. I mean technically if you removed the cotton you...
  2. drunkenbatman

    Kanger Subtank Issues

    *stares at the ground in shame* In my defense, it was 8am after an all-knighter. I'm changing my post, but leaving the intentional misspelling in this sentence just to aggravate you. :)
  3. drunkenbatman

    Until you have made your first 5 posts...

    Hey mate, welcome... again. I don't know but I've been told that after a period of inactivity your account can go dormant or such to prevent spam, but obviously you're able to login so I don't know. Your best best is probably to contact a mod -- head to the post listing and look on the bottom...
  4. drunkenbatman

    Coil help

    Wow, you guys are super helpful. You have also ruined my experiment to see how deep State O' Flux's well of patience goes, so now I have to return all the money in the pool. I hope you're proud of yourselves. :closedeyes:
  5. drunkenbatman

    Kanger Subtank RBA Pre-Built Coils Opinions?

    Not with the ones from them, which apparently have Kangertech on the bag, but with those types of things in general: yes and they're fine. You can get them in packs of 50 for $3 in a variety of resistances from fasttech without the cotton. I don't generally use them, but not due to their...
  6. drunkenbatman

    IPV 1 35 w and Kanger Subtank

    Hey mate! First of all, welcome. Second of all, what Puhn asked goes for me too -- as well as whether or not you've tried another atomizer on it. :)
  7. drunkenbatman

    Coil help

    Hey mate! Unfortunately your post is very, very vague. Chances are you're going to want to be looking at things like parallel wires and twisted wires for more surface area. Go on youtube and check out "twisted messes" and give yourself ideas. I'm also going to send you Flux's page because he...
  8. drunkenbatman

    Rebuilding Atlantis coils

    @mrfrankpdx You can also easily rebuild the OCC coils on the mini, practically easier than the RTA. :) @Bmr23 Which technique to rebuild are you using? Wicking can be really rough, here are two links for rebuilds I stole from Susan (hi susan): vertical...
  9. drunkenbatman

    fogger v5 no taste.

    Heya mate, I can't help at all on the fogger, but for the V4 here's two links from my notes that may be of help: Logo and serial nr.: FastTech Forums Logo and serial nr.: FastTech Forums If something works, let us know hey? :)
  10. drunkenbatman

    Kanger Subtank Issues

    Hey mate, There's two screws on the bottom of that mod, the big knurled one and the one you adjust for your battery. Try unscrewing the thick knurled one a bit, then screwing in the igo-w, then screwing in the knurled mod, then the adjustment pin.
  11. drunkenbatman

    Battery charging safety: Wall charger vs micro USB

    Hey mate, found you wandering deep in the thread wilderness so hopefully you're still around. You got a solid charger, so you're set there. There are generally two reasons why it's recc to charge outside of the device: 1. It's generally much faster as I believe the builtin is 500 milliamp. 2...
  12. drunkenbatman

    is anyone else having wicking issues with the kayfun v4 clone (fasttech version A)?

    Hey mate, found you wandering far in the weeds -- and unfortunately I don't have a v4, and the only thing I have in my head is to have the juice flow fully open then tighten the airflow down. It may also be you're blowing too many watts for it to wick, but I know you aren't the only one having...
  13. drunkenbatman

    Xpro M50 'Check Atomizer' Help

    Hey mate, found you on page 17 so not sure if you're still with us or not -- but "check atomizer" on the m50 basically means the ohms are registering really low or really high (<0.2 or >9). One of three things is most likely: 1. Issue with the coil shorting (change the coil) 2. Issue with the...
  14. drunkenbatman

    heres a vapor beast deal.

    You're welcome, I'm glad my childhood trauma is being put to good use. Also, 4:40am bump for Smokey. You're welcome again.
  15. drunkenbatman

    Hi I'm new here!

    Missed this, I obviously have to come up with a better organization system for my tabs. :) You're 100% right, and the short answer is that you can't know what's going into it unless you do it yourself. You can *hope* people are observing levels of hygeine and cleanliness, but not always and...
  16. drunkenbatman

    People who went from cigarettes to vaping: Have you noticed health improvements?

    I got nothing on the pains and freezing, but you really need to be on the lookout for depression when you stop smoking, and both it and and the constipation are classic withdrawal signs. The normal suggestion would be to either vaping more to get your levels up so you can even out naturally, or...
  17. drunkenbatman

    Tunnelno5 Introduction: KFL+V2 (Pics of build)

    No worries on the terminology, only filling you in so we can help you better in the future. :) That's actually really interesting, how common is it there in vape shops? I'm assuming the shop also sells pre-mixed, and getting the nicotine on the side is an option? We just wanted to make sure...
  18. drunkenbatman

    Copper Tobh Atty (clone) modification ?

    Hey mate! 1. In terms of the side-slots you're thinking of cyclops holes, where you connect the existing holes. Obviously there are lots of ways to do this, but the easiest really will be with a solid dremel as mentioned by Phun. Since it's copper you could get by doing this with a drill over...
  19. drunkenbatman

    crazy

    You're mocking me, aren't you. :glare:
  20. drunkenbatman

    Dripping through the tip?

    Just the tip, mate. It won't hurt, I promise. Have fun figuring out what to do with that line, mods.
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu