Search results

  1. Elendil

    Attempt # 26--My quest to build one working coil

    Here is the resistance: It is a little higher than I was aiming for. I wanted 1.2-1.3 but decided to go with it as is.
  2. Elendil

    Attempt # 26--My quest to build one working coil

    My KFL+ Black that I got on the classifieds arrived yesterday. I though I would try building a coil for that just in case there is a problem with the channels on my first KFL. Here is the coil I built:
  3. Elendil

    Mt Baker juice steeping?

    I maintain that "steeping" is a myth. After 5 years, no juice I have ever tried tasted any different 2 weeks or months after I go it than it did the day it arrived. Good is good immediately and bad is bad immediately. Time makes little difference. How you perceive a juice can certainly...
  4. Elendil

    Attempt # 26--My quest to build one working coil

    Exactly. You haven't lived until you've pulled a set of triples down an interstate that is solid ice with a 40mph crosswind. Good times. Definitely not a task for your standard license holder
  5. Elendil

    Attempt # 26--My quest to build one working coil

    Not sure if I will be doing anything tonight. Just leaving Toledo with a 320 mile drive ahead. I'll check in later .
  6. Elendil

    Attempt # 26--My quest to build one working coil

    I have been up since 4:30am. Going to have to pack it in for tonight. I'll build another coil tomorrow with more wraps and see how that works out. Thanks to everyone for your help tonight. I think we are getting closer....... Hopefully by the 4th of July.........
  7. Elendil

    Attempt # 26--My quest to build one working coil

    I had already trimmed and tucked and filled by the time I saw your post. Getting vapor. It is just very warm with again no taste. Not burnt. Just no taste at all. The tank is getting warm. Not super hot, but pretty warm
  8. Elendil

    Attempt # 26--My quest to build one working coil

    MY draw has been about 5 seconds
  9. Elendil

    Attempt # 26--My quest to build one working coil

    3 strand wick. Where do I trim it at? How long?
  10. Elendil

    Attempt # 26--My quest to build one working coil

    So back to more wick now? Yes still using the standard drip tip that came with the unit.
  11. Elendil

    Attempt # 26--My quest to build one working coil

    Here is the wick I just pulled out
  12. Elendil

    Attempt # 26--My quest to build one working coil

    Found a standard paperclip. It will not go down the juice channel with the chimney screwed in place.
  13. Elendil

    Attempt # 26--My quest to build one working coil

    .98ohm juice 50/50 finding a paper clip......
  14. Elendil

    Attempt # 26--My quest to build one working coil

  15. Elendil

    Attempt # 26--My quest to build one working coil

  16. Elendil

    Attempt # 26--My quest to build one working coil

    From what angle do you need the pic?
  17. Elendil

    Attempt # 26--My quest to build one working coil

    Here is where I got it: EHPro Kayfun Lite Clone
  18. Elendil

    Attempt # 26--My quest to build one working coil

    Did as you described. Total burning taste now. Very low vapor in both vapes. Battery should have been fresh. But just in case I pulled a freshly charged one and switched it out before doing your procedure
  19. Elendil

    Attempt # 26--My quest to build one working coil

    Took 10 draws. The first 6-7 were "ok" at best. about the same amount of vapor that I get from my VTR with an i30s. (medium amount at best). The 8th draw I got some juice in the mouthpiece The last 2 draws I'm starting to get that burnt taste again. Not as severe as in previous build but it...
  20. Elendil

    Attempt # 26--My quest to build one working coil

    I'm almost afraid to try it. I'd just like to sit here and look at it and imagine that it works........... Here goes.........
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu