Search results
-
House of Hybrids featuring the Zenesis PV
what's the purpose of this mod? is it just for looks to show more of the provari top cap? or does it remove any wobble from z atty when sitting on the provari- silversx
- Post #79,791
- Forum: E Cigarette Suppliers Forum
-
The new PHOENIX XL REBORN - ITS BEEN REBUILT!!!
honestly i can't find any fault with the old ones... the only thing i do when i first start a new one is take trim the wick a bit so it's not completely blocking both holes.. then it lets air out and wicks perfect.. i have two genesis attys.. the DID and a Z atty pro and dare i say the old ones... -
The new PHOENIX XL REBORN - ITS BEEN REBUILT!!!
are you using the new ones now? how is the vape.. does it wick well vs the old ones? -
The new PHOENIX XL REBORN - ITS BEEN REBUILT!!!
i think i got a mix up too.. got 2 packs of 510 reborn and got 2 packs of 808.. and i have no adapter.. doh also the juice capacity looks to be less than the old ones.. even from just looking at it.. the space is a lot shorter.. -
-
New at Clouds of Vapor!
when can i vape this in a penelope? :D.. dying here..- silversx
- Post #3
- Forum: E Cigarette Suppliers Forum
-
New Genesis type atomizer by DID!
i didn't know the fill hole screw can be adjusted .. i either take it off or tighten it all the way down.. i figure the threads are air tight once engaged.. i'll try that..- silversx
- Post #7,424
- Forum: Closed Unregistered Supplier Threads
-
New Genesis type atomizer by DID!
can you post a pic? maybe also a shot of the center hole too.. is it hollow or stuff like a sausage- silversx
- Post #7,423
- Forum: Closed Unregistered Supplier Threads
-
New Genesis type atomizer by DID!
i did see some boiling a few times.. so im flooding.. how can i reduce that.. i tried putting the fill hole nut back on but i got dry hit after 2 hits.. the wick top is already pinched..- silversx
- Post #7,418
- Forum: Closed Unregistered Supplier Threads
-
New Genesis type atomizer by DID!
the wick i currently have is 40x40 and i can fit a paper clip thru center... 4/3 wrap @ 2.0ohm... 4.0 on the provari and mediocre vapor at best with the air hole lined with wick.. very frustrating since it seems to be a perfect setup and yet no where close to the ammount of vapor i see on...- silversx
- Post #7,413
- Forum: Closed Unregistered Supplier Threads
-
New Genesis type atomizer by DID!
this is how mine is set up right now.. pretty thick.. with a hole big enough for paper clip.. but im getting mediocre vapor at best.. with no screw in fill hole.. if i put fill hole screw in i get dry hit.. i thought maybe if i made a thin walled wick with a giant hole like a straw i can get...- silversx
- Post #7,412
- Forum: Closed Unregistered Supplier Threads
-
New Genesis type atomizer by DID!
please tell me in your experience everyone which is better for clouds of vapor on the did A. a solid roll of mesh with a tiny bit of hole in middle or B. a fairly thin walled mesh much like a straw with large hole in middle assuming my mesh is 400 and juice 70/30 and rolled to fit snug in the...- silversx
- Post #7,408
- Forum: Closed Unregistered Supplier Threads
-
overwicking killing me
nobody? let me ask a simple question then.. for best genesis performance.. should my wick be: A. a solid roll of mesh with a tiny bit of hole in middle or B. a fairly thin walled mesh much like a straw with large hole in middle :) -
New Genesis type atomizer by DID!
by "loosen the fill hole" do you mean loosening the screw in the fill hole? did you just back it out a few turns? or did you completely remove it..- silversx
- Post #7,365
- Forum: Closed Unregistered Supplier Threads
-
overwicking killing me
how do i prevent my DID mini from over wicking.. im using 400 mesh and 32gauge kanthal.. i use a square piece ofr 30x30 ish mesh.. 4/3 wrap 2.0ohms and i leave the other nut off.. if i put the other nut in the hole.. i get dry hit after 2 drags but if i let the did sit.. first few hits are... -
New Genesis type atomizer by DID!
when i use the other nut to close off the 2nd hole.. i get dry hit after one or two hits.. if i leave the nut off i think my wick gets flooded because i have mad throat hit and flavor but mediocre vapor even with cap hole aligned with the wick.. is there anything i can do when making a wick to...- silversx
- Post #7,360
- Forum: Closed Unregistered Supplier Threads
-
New Genesis type atomizer by DID!
thanks for the tip.. it does seem to produce more vapor after 2 or 3 consecutive hits.. but i already have the wick pinched at the top.. could this be caused by too much mesh material or too thick of a wick? when i look at the wick from just sitting for a while it looks normal and not overly...- silversx
- Post #7,345
- Forum: Closed Unregistered Supplier Threads
-
New Genesis type atomizer by DID!
hi all so i finally made a wick with 4/3 coil that reads 2.0 ohms.. using 400 mesh and 32gauge kanthal.. no hot spots.. perfect glow.. but i get mad throat hit and not as much vapor as i do with a ce3 bottom coil.. i have the did mini and the hole is lined with wick when tightened.. are...- silversx
- Post #7,343
- Forum: Closed Unregistered Supplier Threads
-
310Vapers: ORION v2.1 ON Sale Now!
ordered one! woohoo .. sold out now- silversx
- Post #6
- Forum: E Cigarette Suppliers Forum
-
what do you use to oxidize your SS mesh?
i oxidize the crap out of my mesh but always after rolled up.. i still get shorts and have no idea why.. i would literally sit there and use a butane torch on it for 30 minutes.. pop it in my DID and still get shorts.. wth...