Search results

  1. bapgood

    Printed DNA30 Bottom Feeder

    Here is my first go at using the new hollow center pin. I used the indoor lathe (drill and Dremel) to grind down a 14g hypo needle so it just slips through the pin. I wanted some sticking out the top (but probably not that much, I will probably trim it), then I was thinking I would drill out...
  2. bapgood

    Printed DNA30 Bottom Feeder

    Get some SS flux and stainless is actually not bad at all to solder. But your going to want to clean real good after word, because I don't think it's something you want in your juice :D
  3. bapgood

    Printed DNA30 Bottom Feeder

    Ok....I have been super busy and just speed read from post 490 :lol: Couple things I can comment on. - I can say 100% for sure the new DNA has built in RP protection (but I can't or wont say anything else) - Yes Fat Daddy is very open to suggestions, and I talked to him in length after he...
  4. bapgood

    Mike n Tibs DNA Mods!

    Did someone say SxS......:lol:
  5. bapgood

    Mike n Tibs DNA Mods!

    Yeah I have a couple of SX350's that needed to be built up. But probably the last ones I'll build.
  6. bapgood

    Mike n Tibs DNA Mods!

    This is why I love Cerakote.....These were done with zero prep and two coats and then into the oven @150* for two hours. These were some other projects over the weekend. Sorry the pics kind of suck. The green ones are Duracoat zombie green cleared with Cerakote high gloss clear. The Black...
  7. bapgood

    Mike n Tibs DNA Mods!

    You could do a Cerakote clear after your paint and clear. It's pretty dang hard!!!
  8. bapgood

    Printed DNA30 Bottom Feeder

    Well done!!!!
  9. bapgood

    Printed DNA30 Bottom Feeder

    150* for 2 hours
  10. bapgood

    Printed DNA30 Bottom Feeder

    I have also used Duracoat which is a epoxy paint. It's a little bit thicker but works.
  11. bapgood

    Printed DNA30 Bottom Feeder

    I use oven cure, mainly because its their staple product and is offered in the most colors, it also makes for a quick process. Paint and then 2 hours in the oven and its ready to go.
  12. bapgood

    Printed DNA30 Bottom Feeder

    gdeal answered most of this, but here is my reasoning. White is cheaper. The dyed black is still porous as well as easily prone to scratching and etc. From my experience it isn't always done to what I would consider a satisfactory quality, it can be uneven/blotchy/etc. Cerakote has proven to...
  13. bapgood

    Mike n Tibs DNA Mods!

    Like have said before, the instructions are just how I do it and I'm sure there are other ways that work. Just a couple of notes. - I run the positive wire along the top and then down, so it doesn't interfere. - I don't actually solder the wire in the holes. I fill the holes with solder and...
  14. bapgood

    Mike n Tibs DNA Mods!

    Haha.....yeah originally I was worried about getting the nut started and tight on the 510. But the new way has proven to be much easier.
  15. bapgood

    Printed DNA30 Bottom Feeder

    Damn that brass ring and button turned out good!!! The only credit I get on this is painting it. Well done gdeal!!!
  16. bapgood

    Mike n Tibs DNA Mods!

    Here is a google doc to the Tibs assembly instructions - https://docs.google.com/document/d/1-ugYXwwJmr9CkThiu1tKh6lEozf4pORLhZA_KLqA7kg/edit
  17. bapgood

    Mike n Tibs DNA Mods!

    You didn't follow the directions....:lol: Did this work? Or did you end moving the wire?
  18. bapgood

    The YiHi SX350 35W Chip at Varitube

    The flat and angled lid are the same height, so yes the flat lid will work also.
  19. bapgood

    The YiHi SX350 35W Chip at Varitube

    Kurrpt....Remember you are in Varitube's supplier thread not a modding thread/etc. If you want to buy one cheaper somewhere else, that is fine. Just be respectful and keep it to your self in this thread.
  20. bapgood

    Printed DNA30 Bottom Feeder

    ............
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu