Search results

  1. k702

    All my batteries or maybe the two chargers are shot already??

    that depends on what you mean by bit the dirt. If you over discharge the battery (meaning use it to 3.2 volts or below,) it should be able to charge it no problem.. If you've used a battery to power an atty with a hard short and actually messed up the chemistry of the battery bringing it...
  2. k702

    All my batteries or maybe the two chargers are shot already??

    http://www.xtarlight.com/05-chanpin/p-001-1.asp?styleid=233 will revive batteries that have gone past their over discharge point. comes with a 2 year warranty, easy readout that gives you the current voltage of your battery when you put them in the charger. never gets warm let alone hot, has...
  3. k702

    nemisis possible button malfunction

    what resistance is your patriot at? do you have an ohm meter to check for shorts? if there is a hard short in the build of the atty it won't matter how well you've done putting the mod together. and you could do damage to your battery by firing it again and again trying to figure out what's...
  4. k702

    nemisis possible button malfunction

    does the battery rattle with everything tight? There is a kick ring that's about 3mm if you don't know to look for it you won't see it, check to see if it's on, if it is take it off as it will extend the tube too far to fire properly without a kick in the mod. if that isn't the case then...
  5. k702

    All my batteries or maybe the two chargers are shot already??

    what brands/models are your chargers? what are the brands of the batteries? by not working do you mean they aren't charging when put on either of the chargers? Do you have a multimeter? If so use it to check the voltage of the batteries that don't seem to be working. let us know what...
  6. k702

    nemisis possible button malfunction

    unscrew the button. Tighten down the silver pin. Put the button back on the mod. Put the battery in the mod. put the top cap and your attomizer on the mod tighten down. Screw up the button until you get a little resistance.
  7. k702

    About to rage on local vape Shop

    No offense meant here... A mechanical mod is a pretty simple thing... even if the switch was press fit there would be ways to get it apart and see what would need to be done to get it working... throwing it away makes little to no sense. As for the 4nine, youtube would probably help you...
  8. k702

    How Much have you $aved Vaping?

    8 months a little under $1,500.00
  9. k702

    Leaving your atty in the car

    I think that might depend on the weather where you live. Here in vegas it can get up into the 110's.. Here and Arizona have both hit 120's in recent years... Incredibly hot and a car sorta acts like an oven. There is a conversion rate somewhere to figure out how hot the inside of your car...
  10. k702

    So, how much has your 'hobby' cost you?

    my vaping habit has actually saved me a little under 1500 bucks in a little under a year. Spending can be easy to keep in check...
  11. k702

    .18 ohm coil on Sony vtc 5

    Is it within the recommended safe range for that battery? barely... if you want any type of realistic headroom for safety then no.
  12. k702

    Cutting Teeth (literally)

    seconded. A dremel could be 60% of your toolbox for a lot of things if needed.
  13. k702

    .15 ohm build

    Having to ask this question means you shouldn't be asking this question... is that a paradox?
  14. k702

    How do you feel about...

    I don't do certain things around little'n's just to try and set a good example. You know, with the hope that they'll pick some of the good mannerisms up. No cussing, no real anger, no gettin' drunk, do my best not to act too stupid, and no vaping. It's just how it is in my world.
  15. k702

    You won't be seeing Baditude posting on ECF in the near future

    fingers crossed everything works out sooner rather than later. I'll miss being able to reply to battery threads with "baditude will be along to give you the correct answer in a few I'm sure." until you get back.
  16. k702

    RDA is TOO HARSH help!

    can we get some pictures of your build(s) before you tear them(it) apart? You don't have any hot legs or hot spots do you? (fire the mod with the top cap off and look for anything turning red) Even with perfect airflow and wicking a hot spot will ruin an otherwise beautiful vape.
  17. k702

    Rda in flames!

    edited - read a number wrong delete pls thnx lol
  18. k702

    Authentic makers sueing Cloners?

    Not sure where the first part comes from... Obviously there is a market for authentic 250 dollar copper tubes with fancy artwork.. It's just not nearly as large as the market for 50 dollar copper tubes with fancy artwork. Hence many mod makers putting out like 200 or 500 pieces of product...
  19. k702

    Authentic makers sueing Cloners?

    didn't use it as an analogy I used it as a common term, maybe raking you over the coals would have been a better choice of words? What I have a problem with is that it seems that a few of these authentic mod companies put as much or more thought into stopping clones than they do making stuff...
  20. k702

    Authentic makers sueing Cloners?

    bleh, keep defending people that are [Moderated for offensive term] you for a box(made by someone else) with other people's tech inside or a metal tube many times with ripped off art plastered on it and a pretty universally ripped off switch and top cap design. Originality? Innovation...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu