I am into water cooling PC's and if I had $1 for everyone that wandered into a watercooling forum and said "I cleaned my res with Isopropoyl alcohol and it cracked!!!!", I would have a lot of dollars. :)
The mini Protank 3' are problem free (in my experience) right out of the box, and the Protank 3 just needs an airflow control valve. The base that comes with it is horrible.
If you are not feeling adverse affects and actually able to put it down from time to time, you should be good.
However if you can't put it down, maybe your nic is too low. I started with very high nic (36mg) and was able to vape pretty much equal to or less than I smoked. Since I have dropped...
An airflow control valve could help that Protank 2 as well. I've heard tell of people using them on the minis as well. They are less than $5 is you shop around.
I have one and it rescued me from an annoying whistle and airy draw on the Protank 3.
I recently started making my own coils with 30ga Kanthal and cotton for wick. I use a VV Ver 3 and it has the same wattage limitations as your MVP. When using the Kanger coils, 7.5W was usually fine for me, but since making these coils which range anywhere from 1.6 to 2.0Ω 10-11 watts works...
Sorry to go off topic, but I used to work on Snoqualimie Ridge. :)
Oh yeah, and my avatar pic was taken by my sister at Jay Berry's in North Bend...that is a glass of Snoqualmie Falls beer I am drinking. Good beer.
Funny, this showed up a little while ago too.
http://www.e-cigarette-forum.com/forum/new-members-forum/553151-how-do-you-figure-out-resistance-all-fancy-stuff.html
Also, some video help...
Nano Micro Coil build for Kanger Protank 2 - YouTube
I meant this one, but watch both...
Mini Protank Micro Coil Rebuild
Of course, check your resistance before using... this was my first attempt...
That would have been bad to use. :ohmy:
The Ebay seller I got my 100' roll for $4.99 from doesn't have any more listed.
Oh wait, I forgot I was watching another one - Kanthal A 1 Wire 30 Gauge 01 Resistance Heating Wire 100 ft Spool | eBay
For that device (I did find where it had the battery as well) it probably doesn't. If you go variable voltage, variable wattage or mechanical mod in the future, you will probably have outgrown that carto as well.
I should probably explain more. What you have there is a very basic device and...
I looked around and the coil resistance is not stated that I could find. You need a ohm meter.
Like this - Atomizer Ohm Meter Free Wick and Wire | eBay
It looks like that is a cartomizer, so I assume you have a battery to go with it?
The Itaste VV Ver 3.0 is about the same size as a Vision Spinner 1300, which was my first device. I stick both in my pocket when walking around and have nary a problem.
Except when I leave them in pocket when I get into my car...let's just say that with the seatbelt on, I can't take them out of...
This thread should help -
http://www.e-cigarette-forum.com/forum/clearomizers/486794-protank-microcoil-discussion.html
Rebuilding the dual coils are the same as the single coils. I've gone with all single micro coils for the PT3/Mini PT3 that I use for the Mini Protank 2.
I found this article while struggling with vaper's tongue a couple of weeks ago.
http://www.ecigarettedirect.co.uk/ashtray-blog/2014/03/vapers-tongue.html
I see you are past it, but it can come back in varying degrees. Usually when my juice goes flavorless on me, I switch up juices. A few...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.