Search results

  1. DonG

    quick mosfet question

    Could have sworn it worked without the resistor last night. Now getting a little over 2v through the mosfet without pressing the on button. Going to try the resistor and will post back.
  2. DonG

    quick mosfet question

    Thanks again guys. Looks like P it is. Fried my N bench testing before assembly. Rookie mistake assumed the center pin would be the gate/switch. Lol. Then got the source and device leads reversed and damn thing would not completely turn off. Did not realize they were one way current flow like...
  3. DonG

    quick mosfet question

    Thanks Java. starting to piece together my first wood mod. Single 18650 with 04050 booster. Have a 47k pot I was thinking about adding to make it vv too. A recommendation for the p or n and placement would be great. This will be my first use of a non mechanical switch.
  4. DonG

    quick mosfet question

    Also have a couple of these: http://doc.chipfind.ru/anpec/apm2023n.htm
  5. DonG

    quick mosfet question

    Or this one...cleaning up shop and hope to find one I can use without spending money. APM3095P datasheet - P-channel Enhancement Mode Mosfet
  6. DonG

    quick mosfet question

    Is the irf630b suitable for use with tac switch?
  7. DonG

    Making the roughstack vv?

    This may be a good option for you. http://www.e-cigarette-forum.com/forum/e-cigarette-mods-reviews/284473-kick-evolv.html
  8. DonG

    Wick materials. Safe vs dangerous.

    Cheesecloth
  9. DonG

    Smallest P channel Mosfet?

    Too simple. Thanks.
  10. DonG

    Smallest P channel Mosfet?

    What is the difference between p and n mosfets?
  11. DonG

    Just wondering what you all do to fix a 510 connector?

    Made that mistake. Now I clean all excess soldier from the tip of my iron, dip it in flux, and touch it to the center pin. The excess blob is drawn to the iron and makes removal of the pin easy without damaging the gasket.
  12. DonG

    Just wondering what you all do to fix a 510 connector?

    If you have dead cartos around just take one apart. The center gasket is the same as used in the battery connector and makes A free replacement part. Done it a few times.
  13. DonG

    burn taste and burn smell

    Lack of airflow like an open air burn will also cause coil overheating. It should be better in an atty with a good wet wick.
  14. DonG

    I've been searching for wick materials...

    http://www.e-cigarette-forum.com/forum/modding-forum/284030-wick-materials-safe-vs-dangerous.html Good discussion on this thread. Good results being gotten with cotton/organic wicks. Cheap and locally available too.
  15. DonG

    LRvsHR

    LR does draw more power so based on the crude volt drop test the #1 atty is lower resistance.
  16. DonG

    LRvsHR

    I have both 32 & 34gaA wire. The 32 measures 1.3ohm/in; the 34 is 2.0/in. So a 3.0ohm coil will need 1.5"of of 34 or 2.3" of 32. Consider the amount of space you have for the coil when picking a wire size. At 2.0ohm I like the 32ga better because I can spread the heat over a couple more coils...
  17. DonG

    Wick materials. Safe vs dangerous.

    Cyrus......maybe try leaving 1/8inch or a little more wick exposed. It may swell up enough to slow or stop the flooding vs being trimmed flush.
  18. DonG

    Drip Well?

    Really nice work there.
  19. DonG

    LRvsHR

    What ohm did each one test at?
  20. DonG

    Wick materials. Safe vs dangerous.

    How to keep the coil wire from shorting in the tubing?
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu