Search results

  1. WillyB

    Charger Assistance.

    That's one heck of a charger, seldom have I seen ones that charge at that high a rate, which in general is much too high for 14500s. Something in the 400 - 600mA range seems more appropriate.
  2. WillyB

    Phoenix/Chalice Vertical Cotton Wick Setup

    Many folks have problems with SS wicks cuz they end up squishing/distorting it with their coils. You need to just lay it onto the wick. When one or more wraps bite too tightly into the SS mesh that's when problems (shorting) can occur. This is also a fine method to use for SS...
  3. WillyB

    Bizarre kGo deaths

    Well I guess you could check for connection problems, mostly the center positive post which can get pushed in by over-tightening. Atomizer and Cartomizer Connection Problems | Vaping Guides to the Electronic Cigarette For our uses inexpensive meters can help in troubleshooting. You should have...
  4. WillyB

    Need help Ohms vs. Volts w Attys & Cartos w/ my Silver Bullet

    While I kinda agree, but there are actually a lot of significant factors that influence the vape at the same watts. We don't vape watts. Even different gauges of wire in the same atty, even if the ohms are identical will vape differently. The original DSE901 and 801 which had nearly identical...
  5. WillyB

    Stacking Batteries?

    FWIW those numbers would not bother me in least. You might try alternate channels when charging, it's not unusual for different sides to charge a tad higher/lower. You should also alternate them in the PV after charging. You could then re-meter them when they quit and see if the voltage...
  6. WillyB

    atomizers for buzz pro

    Avid Vaper : Personal Vaporizers and Accessories
  7. WillyB

    Revival of dead thread?

    I guess that is a judgement call that will have to with relevance and it depends on how old it actually was. I always like to see new folks ask a question and then refer/reference an old thread. Shows they are using the wealth of information that is available on these forums.
  8. WillyB

    ?s about pg/vg mix.

    Probably? :) Seems best to actually vape it first.
  9. WillyB

    homemade atomizer bottom feed

    What elements? Will you be storing yours outside? @ cry Very, very nice and the no soldering assembly is sweet and elegant. :thumb: And for those who feel a ceramic atty cup adds to the experience the down tube could be blocked, and a side hole top cap could be used to make it a...
  10. WillyB

    Strange (or maybe not) Question

    He has gone to using a drop tube from the top (notched into the drip tip) for an air inlet. Should offer quite a bit of tweakability, length position ect.
  11. WillyB

    Kanthal vs Nichrome

    You'll note most always flame treat any resistance wire before wrapping.
  12. WillyB

    Strange (or maybe not) Question

    LOL. That's Michal Jansto's WillPro. He's pretty much the father of the modern Genesis. He was also the first to espouse wrapping the SS wick, with everything from paper, cotton and various braids, which was met with a certain amount of scorn at the time.
  13. WillyB

    What Flavor Are you Vaping Right Now?

    Interesting, from the site: I wonder who the "#1 e-Liquid manufacturer in the world" is? :)
  14. WillyB

    Will a 2ohm DCC work ok at 3.7V?

    When did regulated come into the picture? He's got an SB. Why should that matter? Did you read the original post?
  15. WillyB

    ego twist mod?

    Never once said anything about it not working. (???)
  16. WillyB

    Will a 2ohm DCC work ok at 3.7V?

    From my post, your words.
  17. WillyB

    Yuck. :(

    Seems like a no-brainer, get some bottles of USA mix from Vaporbeast seeing as you "really liked" it. Two popular Dekang liquids are DK-TAB and Flue Cured. MadVapes has good prices on 50ml bottles that are within your stated budget.
  18. WillyB

    Can't get 801 fusion to work

    Why ignore the guy who sells them and who probably has gone round and round many, many times with this adapter you went with? Forget about 'pops', learn to count turns after you make contact with the shell. Sounds like your carto is dumpster bound.
  19. WillyB

    Need help Ohms vs. Volts w Attys & Cartos w/ my Silver Bullet

    :) They most certainly are actually 1.5Ω. No matter what the combination is, series, parallel, both, one coil or ten, the watts consumed are identical if your meter reads the combo as 1.5Ω.
  20. WillyB

    Will a 2ohm DCC work ok at 3.7V?

    Just go to a 2Ω single coil, Boge or Smok, try both. For tanking, the Boge will work best, they are much more forgiving when it comes to hole(s)/punch size.
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu