Search results
-
Ok Noob mode - I need an quick introduction to Mech MODS
You can get away with using a lower continuous discharge amp rated battery in a regulated mod but they should still be IMR chemistry for safety and due to the Pulse Width Modulation which will fire at higher volts for a certain amount of time in order to reach your set output voltage in some... -
Ok Noob mode - I need an quick introduction to Mech MODS
high drain IMR is what should be used in any e-cig mod regulated or non regulated, kicked or not kicked. The specs I gave were for the Kick2 by Evolv which right now is regarded as the best kick module out there. -
***Knock Knock Juice Giveaway***
Good luck everyone! I liked this contest!- PhatRon
- Post #110
- Forum: E Cigarette Suppliers Forum
-
Ok Noob mode - I need an quick introduction to Mech MODS
Yes you are correct about the Kick turning your mech into a VW device. Here are the specs for you and for others who view this thread and are interested: Output Power- 5 Watts to 15 Watts Output Voltage- 2 Volts to 6.3 Volts Output Current- 6 Amps Atty Resistance- 0.5 Ohms to 3.3 Ohms Low... -
MadVapes Weekly Contest - April 14 through April 18
I like the idea of e-cig history or some type of math problem maybe with ohms law or maybe like a caption the picture contest. Those are always fun too! -
4/13-4/20 Ginger's USA Running Give-A-Way!
TVR RY4 12mg 50/50- PhatRon
- Post #27
- Forum: The Vapor Room
-
A 12V charging plug would really come in handy
I use a standard wall outlet in my house and the iphone cube to plug my ego charger into it to charge my ego. It works just fine. If you read the back of the cube where the two prongs are it says that the input is 100V-240V and the output is 5V and 1amp so you can use it if you use your inverter...- PhatRon
- Post #2
- Forum: New Members: Introduce Yourself!
-
Ok Noob mode - I need an quick introduction to Mech MODS
People usually use 1.5ohm coils or lower on a mech, anything higher you are basically not going to notice much of a difference compared to a regulated device like the MVP2 (not including any of the DNA decives or the SX200/350 which will regulate sub-ohm builds). You probably hear about... -
Ok Noob mode - I need an quick introduction to Mech MODS
To answer some of your questions: You are correct in the fact that mech mods make a connection when the button is pressed if you have the positive and negative contact pins adjusted in the correct position. Mechanical mods are unregulated so they output the amount of charge that is in the... -
LETS GIVE SOME STUFF AWAY! $100 Gift Certificate to the winner!
#2 Reese's Peanut Butter Eggs are so yummy!- PhatRon
- Post #16
- Forum: Smokeless Image
-
LETS GIVE SOME STUFF AWAY! $100 Gift Certificate to the winner!
I like the time spent with family.- PhatRon
- Post #15
- Forum: Smokeless Image
-
***Knock Knock Juice Giveaway***
knock knock who's there? Yoda Lady Yoda Lady Who? Hey! I didn't know that you could yodel!- PhatRon
- Post #10
- Forum: E Cigarette Suppliers Forum
-
Kanthal
These might help you out some when starting out. Remember to account for the length of the legs but that doesn't add too much resistance to your build unless you have long legs. With the coil calculator you just enter in your desired resistance and the gauge wire you are using...- PhatRon
- Post #16
- Forum: New Members: Introduce Yourself!
-
1st time dripping. I think I understand now...
You may want to take a look at the IGO line or the Nimbus. They come with pretty small stock airholes which will be a tighter draw that you might like. $10.00- IGO-W RDA <-- Very quick shipping from a US supplier. $10.95- IGO-L RDA <-- Also a US supplier $9.99- Nimbus RDA <-- US Supplier- PhatRon
- Post #8
- Forum: Rebuildable Atomizer Systems
-
*Keystone Vapor Easter Basket Give Away and 15% off*
The best place my easter basket was hidden was done with a simple easter egg hunt. If your child can read it is quite a good surprise. When you hide easter eggs, write little notes included in the eggs that give hints to where the next clue is and number them so they can go to each one next. Of...- PhatRon
- Post #143
- Forum: E Cigarette Suppliers Forum
-
Broke my MVP 2?
If it's the top coil iClear 30 then just unscrew it from the MVP, put a piece of paper towel under the 510 pin and blow into it a few times and it should shoot any liquid inside the center tube out the 510 connection. If it is the 30b then tip it upside down and do the same thing. You can also...- PhatRon
- Post #13
- Forum: Tanks and Replaceable Coils