Search results
-
Hana dna 40 messed up from the get go?
I got one for Christmas as well. Mine came pretty much dead and needed to let it charge for a half hour to vape anything in it. Left if charge for 4 or 5 hours and battery gauge showed full but still had red light showing. (Should have been fully charged in about 3-3.5 hours). I gave up waiting... -
Hanamodz v3 DNA40 display reading problem?
Don't forget about manufacturing tolerances. No prebuilt head will be exactly as marked every time. That particular head you have installed now may read 2.08. When you replace it the next may read 1.7 or 1.9 around somewhere around the 1.8 range, even 2 again. No biggie. -
-
VaporShark rDNA
My wife ordered an rdna40 for me for Christmas on cyber Monday. It never came. Luckily she's awesome enough to have picked me up a Hana Modz dna40 mini so I didn't end up empty handed today. The vapor shark is still on order. She was told mid January when she called them last week. -
This is how you keep a customer!
I live 15min from cig techs Hanover park store. Good people in there.- dimo
- Post #10
- Forum: General Vaping Discussion
-
Have you found YOUR "end all" setup? Let's see it!
My kayfun gets used every single day since the day I got it back in January. Most of the time it sits on my provari 2.5.- dimo
- Post #49
- Forum: General Vaping Discussion
-
CHARGING TO 4.24v ?!?!?!
Lithium chargers are designed to put out 4.20V. I'm not sure I'd worry about a .04V overcharge, which may not even be accurate with a (cheapy multimeter).- dimo
- Post #3
- Forum: Batteries and Chargers
-
Hana Modz DNA 40 vs. Vapor Flask DNA 40
Hana just released a dual 18659 DNA40 mod. $50 less than the vapor flask. -
New info on the upcoming Innokin MVP 3.0!!!
In case people are curious. Evolv also uses a 32-bit arm CPU for their boards. -
Having a Weird Problem With My Kayfun......
It's probably not wicking good. If you are not getting any bubbles at all while using it, you'll get dry hits. How much cotton you using for your wick? -
-
-
-
box mod vv/vw with removable battery, help
vaporshark rdna40 (new one has magnets, no srews) -
iStick killer?
Larger and costlier? No way this will be an iStick killer. -
How to wire the 1A micro usb charger with dna 40
You need to use the bat +/- to get the required 4.2V charge voltage. The out +/- is a 5vdc output. This board is normally used for stuff like portable battery powered phone chargers. If your battery up to the out pins you'll fry something.- dimo
- Post #16
- Forum: Battery Mods
-
coil needs more heat
Assuming a fully charged battery at 4.2volts and a mech with 0 voltage drop (not really possible) a .7ohm load would fire at 25watts. In reality a mech will have some voltage drop and the battery voltage will drop as its being used. So your watts will drop. You're probably not better off with a...- dimo
- Post #2
- Forum: Rebuildable Atomizer Systems
-
Kayfun pulling too much juice?
Open the airflow more so it pulls less juice or up the wattage, or a combo of both. Some liquid is normal because vapor cools and turns back into liquid near the drip tip area. If you drip tip doesn't reach all the way to the bottom of the well it's sitting in, you're always going to have a... -
Cheap vw/vv holdover device
I also recommend the istick. Great low cost 20w device. Also it's tiny too. Perfect backup device.