Search results

  1. disturbed1

    Wood specialty wood?

    Anyone know where to get some nicer wood like rose or walnut ect. I looked at lose and home depot but all they have is oak.
  2. disturbed1

    Russian 91 Questions

    Just look up kayfun on YouTube
  3. disturbed1

    Converting all my attys into bottom feeders

    Looking good
  4. disturbed1

    Fast Tech?

    Thanks for the info everyone.
  5. disturbed1

    Fast Tech?

    Not sure if this if the right place for this but here it goes. I was looking for some cheap attys to mod for bottom feeding and found some at fast tech. I have never ordered from them befor. I was wandering how long does it usually take to get stuff from them. I know it probably varies but what...
  6. disturbed1

    Painting My Mod

    If you are painting aluminum. aluminum doesn't take to paint very well. You have to use an acid etch primer. You can get a spray can at any auto body supply shop. You dont have to put it on very heavy just a nice dust coat.
  7. disturbed1

    Show your bottom feed RDAs.

    as far as I know you can do this to any dripping atty. I like the drill myself.
  8. disturbed1

    lets see if we can mod this????

    Pull the head apart and install a micro coil and cotton. :vapor:
  9. disturbed1

    Converting all my attys into bottom feeders

    what I did to my cheep A6 atty was drill with a 1/16 through the bottom of the center post . Then use a 1 mm just under the hole for the wire near the deck for the juice. Now with the top cap off it looks like a cyclone.
  10. disturbed1

    show off your mech! homebuilt mods only!

    I finished this a few weeks a go. I drilled out a 510 wish a 1/16 drill and fitted a green blunt tip needle in to it the sweat some solder in there to hold it in place. The I soldered my + right to the ss needle with eez. for the atty I drilled the 510 with the 1/16 droll the the + poste just...
  11. disturbed1

    show off your mech! homebuilt mods only!

    It looks like there is a hole started in the center poste(no doubt a solder point). If so just get a drill the same size and finish the hole. Would that be about right? Or am I not seek it right.
  12. disturbed1

    show off your mech! homebuilt mods only!

    Do you guys think a Fat Daddy 510 could be modded for bottom feeding?
  13. disturbed1

    Just For LM2596 Users

    If you use a tin for a mod do you have to insulate the board so it doesn't touch the tin?
  14. disturbed1

    GUS Mods Upgrade

    Well its way past SEP 15....any news on the G16 and the steam machine ?
  15. disturbed1

    First Mod, Wooden Bottom feeder.

    1/2x1/2 f sweat fitting finishing washer
  16. disturbed1

    Sigelei #19 Tips, tricks, and DON'Ts

    nope did it to mine and its just fine.
  17. disturbed1

    GUS Mods Upgrade

    Im still waiting to here about what new things are coming for the G16
  18. disturbed1

    SO... I'm new

    I would start by finding some recipes that sound good to you. It can take some time to tweak a juice so it just right. Keep in mind that you will make a bad one even when you get good at it. Let them steep most time make a bade juice vapeable .
  19. disturbed1

    14500 Wood Mod w/ Horn Switch

    here are some vary nice box mods Lukkos Puzzle Box V2 with ACS - Cloud 9 Vaping
  20. disturbed1

    First Mod, Wooden Bottom feeder.

    Good luck with that. Let us know how it works. I have a cheep dripper I'd like to try that with.
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu