Search results

  1. d9mel

    Remedy Black (Pluid Clone)

    anyone try the triacetin based absinthe from TFA? The blueberry candy is Tri based and has a "fuller" flavor profile IMO, also clouds liquid depending on saturation and cracks plastic like an 8lb sledge. my shopping carts been making its rounds today, gonna pick some up
  2. d9mel

    Steam Monkey Product Updates and Discussion: Join the Troop!

    Eta on the kick?
  3. d9mel

    Whats wrong with this pic.????

    X2 no juice
  4. d9mel

    Steam Monkey Product Updates and Discussion: Join the Troop!

    Thumbs! I am planning on ordering some staples from your site soon, I'll definitely check that section out
  5. d9mel

    WL bulk flavors

    I just received 4oz Asian ry4 from tfa in a plastic bottle, transferred it to 30ml glass bottles, I'd rather keep flavors in smaller container, less chance of contamination or spill
  6. d9mel

    First Time Tobacco

    Ry4's are a good tobacco to start with IMHO, there's tons of threads on them. They are normally a "caramel & vanilla" tobacco but most vendors have different variations.
  7. d9mel

    need help, again

    I picked up a 1590A, but I was using stiff radioshack wire and couldnt muster the finesse to fit everything in. I like the feel of the 1590G anyways. I'm planning on building another box with 1590G but I'm gonna try for a recessed atomizer design, thats the plan atleast...
  8. d9mel

    need help, again

    Spec, This is the box I used http:// http://www.digikey.com/product-detail/en/1590G/HM841-ND/409858 Its a little larger than the one mamu used, but you don't have to modify the DNA board because of the extra space. If I had to guess on a total price is say around 90$-100$, not too sure...
  9. d9mel

    Stainless Steel mesh, Oxide discussion.

    When SS is welded is there an immediate containment and neutralization process in place for the potential Cr(VI) that might contaminate the heated metal?
  10. d9mel

    Stainless Steel mesh, Oxide discussion.

    Following this concept a hot spot would generate enough heat to create Cr(VI) and cause direct exposure. I'm still using mesh the way I always have
  11. d9mel

    is it normal for RBAs to fluctuate Ohms and what is the reason?

    In my experience any thing over a 0.1 ohm variation is a short or bad contact. I use 28ga A-1 in my genesis and slide the wick out daily, fire and scrub the coil, torch the mesh, then slide it back in using hemostats to keep pollutants off of the mesh as Fed mentioned. I found dry burns with...
  12. d9mel

    Has anyone tried the AGA Tiamat PLUS w/Glass Tank

    Ehuman, I definitely agree with you and the gauge/resistance info you posted. I figured out that setup after a few months of reading threads like this one and wrapping a bunch of bunk coils, the learning curve on genesis attys can be a pain but its worth it in the end.
  13. d9mel

    Stainless Steel mesh, Oxide discussion.

    Subscribed, very interesting
  14. d9mel

    Has anyone tried the AGA Tiamat PLUS w/Glass Tank

    yeah the only reason I can run it is because the DNA puts out a accurate signal, my z max cant run it too well
  15. d9mel

    Has anyone tried the AGA Tiamat PLUS w/Glass Tank

    I agree for matters of sanity. I am not too sane when it comes to vaping though, after tons of experimenting this is what I came up with. 28ga, 10 wraps, twisted top leg, 2.1 ohms, #500 mesh, wick in wick (35 mm outside big hole 15mm inside no hole) airhole drilled to 3/32". i use a DNA 20...
  16. d9mel

    wizard labs shipping cost?

    I normally average about 8$ in shipping. I usually get a good amount of nic and a ton of flavors, packaging is VERY secure. They put a lot into making sure your stuff gets to you.
  17. d9mel

    Casino Vaping...Hit Me!!

    We have a "gaming center" out here an the wife and I go every couple of weeks to watch the horses or spin reels. I carry a unique box mod and got some attention from security the first couple if times I went, but they've gotten used to it. I haven't seen any other vapers unfortunately, would...
  18. d9mel

    aluminum DNA 20 box

    the only wall thickness indicated on hammonds spec draft is 2.5mm, but thats for the back wall I think the sides and door are a little thinner. I tapped and countersunk holes next to the window to fill with epoxy and help anchor it on the aluminum and puddled it out about 3-4mm around the...
  19. d9mel

    aluminum DNA 20 box

    just a test run, made a window out of gorilla epoxy formed into the die cast aluminum. its full of bubbles and distorts quite a bit, so I'm on the hunt for a more optically friendly epoxy.
  20. d9mel

    DNA20 Wood/Metal Box

    Like!! (On mobile)
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu