Search results
-
Another one bites the dust...
I'd replace that spring ASAP and not use the mod until a new one is installed. -
Magnets fell out
Haha same thing happened to me a few months back. I looked for that pesky magnet for almost an hour before I gave up. I got so frustrated that I'd have to buy and wait for a darn magnet. When I went to switch batteries a few hours later, there it was. -
So this just happened...
How does a screw backing itself out cause a short? Any time this has happened to me, it just translates into an anemic vape since the coil leg is making little or no contact with the post. -
Eliquid pooling under rm2
That's totally normal. To avoid this, I put an o-ring in the catch cup before installing the RM2. -
Request: Cosmic Fog - Milk & Honey
Someone posted this yesterday: http://www.e-cigarette-forum.com/forum/e-liquid-recipes/580905-all-you-milk-n-honey-fans.html- FACE MEAT
- Post #2
- Forum: E-Liquid Recipes
-
-
New Capella flavors
Just got an email from Capella about their newest flavors... They're offering a special for a 13mL bottle of each for $14.95 Looking forward to trying the Graprfruit.- FACE MEAT
- Thread
- Replies: 10
- Forum: DIY E-Liquid
-
Hey DIYers
Just an FYI... Most commercially available flavorings are suspended in PG, since it carries flavor much better than VG. If you're allergic or for some reason averse to PG, there's a few threads in the DIY sub-forum that delve into DIY that's entirely free of PG. I have found that liquids heavy... -
What's the advantage of having a bigger atomizer ?
I've got both. I prefer the Cyclone for one reason: its air flow options. The Atomic's smallest holes are still too big for mouth-to-lung inhales in dual coil configuration. The Cyclone's adjustable slots give a nice resistance when adjusted to smallish holes. I like the looks of the Atomic, I... -
Modding a top-feed Cyclone for bottom-feed
Ignorance on my end. That's how the atomizer arrived to me (second-hand). I didn't know that there was a proprietary drip tip for the cyclone until just now. Now that you brought it to my attention, I like the look with the o-ring better than without. -
Modding a top-feed Cyclone for bottom-feed
I used a small socket (with an outer diameter slightly smaller than the base of the Cyclone) on the under-side of the atomizer to allow extraction. Since the positive post and insulator are quite tightly fitted, the use of a hammer may distort the female end of the positive post... -
Picture of Your Setup Part 2!
REO Grand LP, Cyclone AFC, dead cat.- FACE MEAT
- Post #5,921
- Forum: New Members: Introduce Yourself!
-
Modding a top-feed Cyclone for bottom-feed
Update: Cyclone AFC arrived today. The pin was rather easy to extract with a vise. It's in there pretty tight, but it pops loose eventually. I would not recommend using a hammer for pin extraction. I Dremel'd two slots in the insulator with a cutting wheel. Slots were cut 80%(ish) through the... -
Trying to get to a test setup for the Reo
This is all I use to test juices, usually atop a cheapo ego battery. With a paper towel, it takes me less than 30 seconds to change flavors. ETA: They also are fantastic atop a REO! -
atomizers I am working on
I believe the W4's (mushroom tip) cap is slightly larger in diameter. -
Phil Busardo drops some hints...
I assume so. Saying it lies between the current Provari and the P3 also implies that its maximum output is higher than the Taifun Eye. Presumably 30+ watts. I also think it implies that it will be a metal tube mod. -
Phil Busardo drops some hints...
In his review of the Taifun Eye device, Phil hints at some of the upcoming P#'s features. Start video at 5:00 Hmmm....interesting. -
atomizers I am working on
It will fit both. It's an A6 atomizer modded for bottom-feed. 14.2mm diameter.