Search results

  1. Jeremy Evans

    Post pictures of your working wick and coil setup

    Yup that is what I did, qtips not tampon though
  2. Jeremy Evans

    AGA T2 Wick Hole Enlargement Problem

    Hold it tightly and drill slowly, it's not that bad. Just make sure you are using the correct kind of drill bit
  3. Jeremy Evans

    Post pictures of your working wick and coil setup

    Did that too, figured I could try SupeX stuff since it is the beesness
  4. Jeremy Evans

    Post pictures of your working wick and coil setup

    Cotton is cheap, homie. $6 bucks for god knows how many wicks, I have only made a slit in the paper wrapper and taken little pinches off and still end up throwing some away. The superX rolled cotton is going to last forever. I'm sure something will get spilled on it before I run out
  5. Jeremy Evans

    Nimbus Getting To Hot

    Wait, where did you order this from?
  6. Jeremy Evans

    Nimbus Getting To Hot

    Before you proceed, you should stop and figure out what exactly you have there. A quad coil would be dividing it by half twice for example, dual .8 ohm coils would net you .4, now do a quad of same setup you are running a .2 ohm setup. Please do us all a favor and figure out what you are using...
  7. Jeremy Evans

    Micro Coils to increase Vapor, flavor & TH

    hmmm, that is the same as my ADV. The only way I like it now I do anything from 1.6 - 2mm just depends on the gauge of wire, anything really big like 26-28 I do on a 2mm drill bit, 30 and up on a 1.6mm drill bit r a small finishing nail I have that is a hair under 1.5mm
  8. Jeremy Evans

    Post pictures of your working wick and coil setup

    I cant even go back to ekowool, which I thought was the best thing ever when I tried it.
  9. Jeremy Evans

    Post pictures of your working wick and coil setup

    You should pop some rolled cotton in there Jerms
  10. Jeremy Evans

    Post pictures of your working wick and coil setup

    Mkb-ts with Mnke and aw imr's. Just depends, really need a REO though
  11. Jeremy Evans

    Easier way to microcoil 32 GA Kanthal?

    Dual 30 gauge, with 8-10 wraps will net you 1 ohm setup, make sure you are using a drill bit or something similiar to make your coils. 32 is going to be hard to get a lot of wraps in there without being higher resistance. Good luck
  12. Jeremy Evans

    Post pictures of your working wick and coil setup

    I think it is really how long that the cotton takes to fully saturate itself
  13. Jeremy Evans

    Post pictures of your working wick and coil setup

    I would actually say probably around .4-.5, didn't check it. Not sure how I feel about not checking them any more.
  14. Jeremy Evans

    Post pictures of your working wick and coil setup

    26gauge, 9 wraps 1.5mm Inside Diameter, with rolled cotton
  15. Jeremy Evans

    Micro Coils to increase Vapor, flavor & TH

    Today's creation(well, last night actually) 26 gauge, 9 wraps, 1.5mm ID, SuperX cotton wick, I figure around .4-.5ohm, didnt actually check it. I know shame on me
  16. Jeremy Evans

    Post pictures of your working wick and coil setup

    I think 26 is actually a T72 or maybe even an 80 trim
  17. Jeremy Evans

    Post pictures of your working wick and coil setup

    You know it, I would say that 30 -32 gauge is like a little T3/T4 on an old DSM, where as 26-28 is like a good T60 on a Supra, it may take a second longer but when it goes hold on to your .... hole
  18. Jeremy Evans

    Fasttech 'clones'

    I could be mistaken but that is more of a Kayfun clone
  19. Jeremy Evans

    Post pictures of your working wick and coil setup

    My 30 Gauge is pretty instant, I was just getting some lag with the 27 gauge. I redid it last night with some 9 wrap of 26 gauge, It has minimal lag. It is starting to sound like a car forum in here
  20. Jeremy Evans

    Post pictures of your working wick and coil setup

    Maybe I am just a little impatient, or I just need to switch to a fresh batt. lol
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu