Search results

  1. Jeremy Evans

    So apparently, the evic and an xray machine don't mix?

    What was your Evic set on Volts wise? How off was it?
  2. Jeremy Evans

    So apparently, the evic and an xray machine don't mix?

    I would think that with you completing the circuit it would work, but honestly not sure, haven't tried it. I will tonight just to see
  3. Jeremy Evans

    Will sub ohm vaping be a waste for me?

    .5 Ohms, doubled 30 not twisted wrapped parallel on an AGA and not warm either, oh yea air hole drilled out to 1.6mm, thinking about going to 2.0 on it though
  4. Jeremy Evans

    MKB-TS Mechanical Mod (GGTS Clone)

    So I have read through most of this lengthy thread and I am wondering if someone can point me into the right direction for the Stealth style cap that will fit the MKB-TS
  5. Jeremy Evans

    18500 1700 mah batteries for evic or other mod requiring flat tops

    I order similiar batteries from batteryjunction, I think that is what it is and they work fine
  6. Jeremy Evans

    So apparently, the evic and an xray machine don't mix?

    You can check it the same way you check ohm just put the needles on the pos and neg and then set the multimeter to read volts
  7. Jeremy Evans

    Post pictures of your working wick and coil setup

    pdib, you make me want to get a bottom feeder so bad.
  8. Jeremy Evans

    .6 ohms, oh my!

    It worked til I took it off to fire it on the mech and then wouldnt fire anymore after that. Mine works fine all the way to .9 ohm, but I keep them around 1.4 and up on my Evic, I was actually just checking the res for my mech before I fired it up, and thought to my self wonder if will fire and...
  9. Jeremy Evans

    ZAP.. still not blown away..

    The height on the Pos post makes it to where just removing wraps wont work, the resistance will be too low to fire, we are talking about a Provari setup, not a straight mech. I do agree to not go with thinner wire, if anything thicker so you can make more wraps and hit same resistance. Another...
  10. Jeremy Evans

    IGO-L Rebuildable Stainless Steel Dripping Atomizer Anyone have one of these?

    That is why I have been using ekowool, just torch or actually just dry burn it clean
  11. Jeremy Evans

    ZAP.. still not blown away..

    Get yourself some 30 gauge and then you can make a couple more wraps and you'll be in heaven
  12. Jeremy Evans

    IGO-L Rebuildable Stainless Steel Dripping Atomizer Anyone have one of these?

    Guess I need a smaller set of needle noses then, I use to make my coils that way, but with the ekowool once you initially torch it, it is firm enough to not need something inside for spacing like when i was using cotton or small silica, guess I might need to go back to that method for that...
  13. Jeremy Evans

    can a zap be modified into a zau

    The skirt on my ZAP spins but only so much, I thought it was so you could line up your air hole where you want it. Stupid me
  14. Jeremy Evans

    .6 ohms, oh my!

    true, but it worked
  15. Jeremy Evans

    Called out in staff newsletter...

    I find it funny when people complain about not being able to vape here or there. I didnt stop smoking and vaping instead so I could indulge whenever I wanted where ever I wanted, I did it to stop smoking cigarettes. All it takes is one person to complain about something like this and it will...
  16. Jeremy Evans

    IGO-L Rebuildable Stainless Steel Dripping Atomizer Anyone have one of these?

    Does anyone else have a problem with tightening the screws and it pulling your coil? If you do, what can you do to mitigate it? It's a specific type of silica.
  17. Jeremy Evans

    Post pictures of your working wick and coil setup

    Here is a pic of my hybrid wick 500 around 400, with dual 30 gauge 3 wrap, .5ohms
  18. Jeremy Evans

    IGO-L Rebuildable Stainless Steel Dripping Atomizer Anyone have one of these?

    Here is a pic of mine with some Ekowool
  19. Jeremy Evans

    Ihybrid pure

    I dont see why they would cost more? Less material needed for those, however I imagine they will be about the same
  20. Jeremy Evans

    Found a Hybrid Dripper!

    I was all about it til I seen that it was for 14xxx batteries and the video was just stupid
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu