Search results

  1. Hello World

    SmokTech RSST Genesis Rebuildable Atomizer

    Hey ... much appreciated taking the time to measure this for me. :toast:
  2. Hello World

    SmokTech RSST Genesis Rebuildable Atomizer

    What size 'Ming Drip Tip' does the RSST come shipped with? Is it the larger 31.5 x 13.5mm as the Stainless Ming Drip Tip for 510/901/KR808 - large or Cherryvape's Brushed Stainless Steel Ming or the smaller ones usually selling for $4 or so? If not, what size is it?
  3. Hello World

    Mech Mod for AGA-T2

    Here is the Atmizoo Roller with the AGA-T2. ... but expensive.
  4. Hello World

    AGA-T2: Need help to enlarge wick hole!

    ................
  5. Hello World

    AGA-T2: Need help to enlarge wick hole!

    Whether they are rubber gasket design or not, a 3.6 mm wickhole can be cut into the AGA-T2s. I have such beasts, I'm vaping on one of them right now. Cost me $13 a piece, done by a local machine shop. Considering I was spending upwards of $250 a month on cigarettes, this expense to vastly...
  6. Hello World

    AGA-T2: Need help to enlarge wick hole!

    The pic below shows the offset the AGA-T2s need to be milled by to get any decent enlargement. I haven't kept tabs how much juice is consumed since I DIY which costs me next to nothing, so not concerned with that. 9/16 is a good size esp. for 1/8 ceramic wicks. Larger wick hole sizes make a...
  7. Hello World

    AGA-T2: Need help to enlarge wick hole!

    Had mine done by a machine shop, 2 of the AGA-T2 I have done to 9/16, the other one to 4mm.
  8. Hello World

    fc-2000 porous ceramic wick

    If you succeed without damaging it, let me know, as I would also like to take mine up to 9/64. My calculations indicate the bore will hit through the pos. post wall and cause leakage, flooding down through the 510. Also the cap's O-ring seat might get nicked. Myself, I would just sand the wick's...
  9. Hello World

    MVR 1.3 Update

    Around 1,900 hours with 3ml of juice vaped daily each on 2 eVics ... never any problem with them, they work just as well as the day when new.
  10. Hello World

    Who has a Z-Atty-Pro - Rebuildable Tank System please advice

    It's in the coil and the wick setup more so than the brand of genny. My AGA-T2s work every bit as well as the ZAP.
  11. Hello World

    Is this good enough to store nic base in?

    The bottles are good. Personally I don't trust any cap, even Polycaps to last in the freezer for 5 years. There are differing opinions on this, but I always add additional protection by 4-ply polyethelene-wrapping over top of the caps via elastic bands to the glass neck of the bottle. Since I...
  12. Hello World

    Battery question - vamo/sigelei mechanical mod

    You should be good on that. Up to you. The above battery has quite a few Lithium-based safety features.
  13. Hello World

    Provari fire button question

    Ouch!!! Ok, April 1 is gone now. If that info came from anywhere other than Provape I might be inclined to advise to ease of on the shoe polish ... :laugh: One would think this would void a warranty. I'm surprised the electronics would not be damaged. Well, I have a chucker on my hands...
  14. Hello World

    fc-2000 porous ceramic wick

    I think it was mentioned the ZAP wickhole is 1/8 inch in diameter, which is approx. 3.2 mm. I'm not sure if any consensus exists what the best wick size is. I'm not a low-resistance vaper, so what I might prefer might not be the most optimum set up for them. For me anyways, a 3/32 wick is dicy...
  15. Hello World

    fc-2000 porous ceramic wick

    The porosity of these newer CF-2000 is such, that even when an .8mm gap between the wick and the wickhole exists with the fillscrew installed, when laid down flat, does not leak all day, and vapes as good as if the fill screw were off. I shaved another of these CF-2000 wicks down slightly to...
  16. Hello World

    eVic newb questions....

    If it's the same size as the one I mentioned, you'll be OK. The eVic cannot go above 3 amps anyways.
  17. Hello World

    eVic newb questions....

    Google "AW IMR 18650" batteries -- get the 2000 mAh ones ... they'll fit your battery holder. I haven't used the MVR yet, so others could probably tell you better.
  18. Hello World

    eVic newb questions....

    Swap out the stock batteries and use AW IMR 18560 batteries. The heat is primarily a battery issue. As above.
  19. Hello World

    A question for noobs by a noob...eVic or Provari?

    For every hour I use the Provari, I use the eVic for 10. Now I'm mostly doing mechanicals, but use the eVic for setups and diagnostics on gennys and vaping high-end flavors.
  20. Hello World

    rebuildable atty info needed...

    Ceramic wicks provide the cleanest tasting vapes.
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu