Search results

  1. rawr

    Best RDA under $40?

    Aqua produces quite a bit better flavor than kayfuns! Info from first hand! I had to diluted my coconut diy juice because it was too aromatic with 15%... lol
  2. rawr

    Best pg/vg mix

    I like 50/50 mix. Mine diy liquid is steeped for 2 weeks and turns out great everytime with 10% aroma :vapor:
  3. rawr

    Question about my Kayfun Lite Plus v2

    Burnt taste means too little cotton and some parts of coil arent touching silica/cotton/ss mesh and they start glowing! Coil should NEVER glow, when fired and the cotton is in the coil and its fully saturated! You are gonna get burnt flavor from too much cotton also, but not as harsh as burnt...
  4. rawr

    Question about my Kayfun Lite Plus v2

    It should look something like that at the end: 5 wraps, 28awg, 3mm diameter and 1.55ohm
  5. rawr

    SvoëMesto Kayfun Lite negative screw slipping

    Yeah online. :) Syringe is also great to fiddle the cotton to the right place! I am using it on all my rbas.
  6. rawr

    SvoëMesto Kayfun Lite negative screw slipping

    You are right! How the hell did i calculate 2mm out of this. lol Its 8mm.
  7. rawr

    SvoëMesto Kayfun Lite negative screw slipping

    It could be some strange problem with mvp also. Can you test another atomizer on mvp? Resistance stays the same? Then is definitely kayfun.
  8. rawr

    SvoëMesto Kayfun Lite negative screw slipping

    Bad. Properly working kayfun doesnt leak. I am using siringe to fill it through valve. Ohms should not jumping up and falling down. Something isnt right! But if it works on mvp2, then there is no short so there must be something else. Mpv/svd are reading resistance just fine in my experiences...
  9. rawr

    SvoëMesto Kayfun Lite negative screw slipping

    For kayfun i have always used 3mm drill bit! 5/16 inch is 2mm which is too small diameter imo. You should use at least 2.4mm or 3mm. Similar size coil leads like yours, 6 wraps 28awg on 3mm bit gives around 1.75ohm! So i am doing 5 wraps = 1.55 ohm to accommodate kick module for maximum power :)
  10. rawr

    SvoëMesto Kayfun Lite negative screw slipping

    So the threads were stripped. That makes sense now. Thats nice and fair that they replaced bad part for new one! Authentic kayfun for 35$ is a dream :) Check FastTech - Gadgets and Electronics for quality (1:1) and really cheap clones in the future ;)
  11. rawr

    SvoëMesto Kayfun Lite negative screw slipping

    Coil looks nice! Maybe i exaggerated with 5-6mm off the airhole, but it should be at least 2-3mm. Your is a bit high, but not a problem at all! Next time try to lower it for 1 or 2mm and you will see what suits you better. So switching screws helped?! Nevermind. It was bad threading on deck...
  12. rawr

    SvoëMesto Kayfun Lite negative screw slipping

    Turn around the coil to the right for 90 degrees! Leads will be clockwise when tightening down. Upper lead on the picture to the right terminal and lower to the left.
  13. rawr

    SvoëMesto Kayfun Lite negative screw slipping

    Mvp will auto shut down when shorting out. ;) Center pin looks just fine. If you wrap the leads once around then there is no way that the wire will snap off. I guess you had a bad luck with that one. They should replace the deck for you!
  14. rawr

    Best charger under 40$

    Haha i saw that, but why would you assume that the lcd is going to break or stop working? Makes no sense :) if you dont know the people who had troubles with non working lcds on their chargers?!
  15. rawr

    SvoëMesto Kayfun Lite negative screw slipping

  16. rawr

    SvoëMesto Kayfun Lite negative screw slipping

    Looks like you have a short on the deck because of the screw?! Not safe to use on mechanical w/o kick at the moment! What about center pin on 510 connector? It shouldnt touch the sides! But its an authentic kayfun so this would be really weird.
  17. rawr

    Best charger under 40$

    You dont buy charger every day so why not invest in new D4 rather than i4? I would instantly! It has some extra functions for different li-ion batteries and it shows estimated charging time :) Its definitely better than i4 which i still one of the best.
  18. rawr

    SvoëMesto Kayfun Lite negative screw slipping

    Screws are little so just wrap both leads around the screws 1 time and then tighten up! Dont forget to lift the coil a bit before tightening up, at the end it should be 3-6mm over the airhole! Works great every time on non flat screw heads which are common on kayfuns. Stupid imo Correct size...
  19. rawr

    Drippers / RDAs

    If you are gonna buy only one rda, then get the magma (1:1 clone), i promise you its outstanding rda! Mine running at 0.55ohm, 50/50 juice TONS of vapor with 18490 red efest battery! I added oring so the airflow ring doesnt rotate freely! Awesome rda! Chocolate by the perfume apprentice is...
  20. rawr

    Picture of Your Setup Part 2!

    Real "plastic" glock?
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu