Search results

  1. SilverZero

    Micro Coils to increase Vapor, flavor & TH

    The lower gauge wire will make it much easier, trying to get a tight microcoil wrapped with 32ga was a pain in my backside.
  2. SilverZero

    Just wanted to share my "unwicked" horizontal micro-coil w/ cotton igo-l setup

    I had the opposite problem with mine, I almost needed a set of vise grips to take it off at first. I ended up removing the bottom o-ring and just using the top one and that solved the problem. The original IGO-L had smaller red o-rings that didn't hold the cap on tight enough. They have since...
  3. SilverZero

    18350 batteries?

    Make sure you're wearing fire proof underwear.
  4. SilverZero

    Micro Coils to increase Vapor, flavor & TH

    Totally disagree. 0.8Ω microcoil 1/16" with cotton wick is WAY better. :vapor:
  5. SilverZero

    Gonna give AVE a shot...Suggestions?

    The only thing I can suggest is to search YouTube for each flavor. I'm sure at least one person has reviewed every flavor they sell.
  6. SilverZero

    Gonna give AVE a shot...Suggestions?

    I haven't tried that many of their eliquids, but Boba's Bounty, Gorilla Juice, and PG Hype were all good. Gorilla Juice is very similar to Boba's Bounty but with a banana flavor, and Hype to me tastes like cantaloupe and nectarines.
  7. SilverZero

    Regular Atty Drippers (A Dying Breed?)

    Yes, definitely don't use rubbing alcohol. And if you go the vodka route there is no need to use Grey Goose; the stuff I use costs me $10 for 1.75 liters of it at my local liquor store.
  8. SilverZero

    Regular Atty Drippers (A Dying Breed?)

    The barrel length is simply the total length of the atomizer. The longer barrel will result in a slightly cooler vape, and if the juice spits at all there is less of a chance that it will end up in your mouth. Personally I prefer the long barrels. I've never used any 306 atty's but I do know...
  9. SilverZero

    Conversions

    It's completely different for everyone, since people run them at different voltages, they take shorter or longer draws, etc. When I was purchasing pre-filled cartomizers I generally read what the vendor stated was its equivalent number of cigarettes and divided it in half, but that's just me...
  10. SilverZero

    Rba problem please help

    Is the coil contacting the SS mesh everywhere? If the coil is too loose and there is a gap between the coil and the mesh you can get a metallic/burnt flavor from it.
  11. SilverZero

    Evod rebuild fail!

    It's possible that the coil leads that you fed down through the center were touching each other. If that happens you'll get a short. If you try again be sure to pull the lead ends snug before you insert the bottom rubber insulator.
  12. SilverZero

    Regular Atty Drippers (A Dying Breed?)

    What I've done with mine is rinsed them out well with hot water then soaked them overnight in a shot of cheap vodka. That usually removes any residual flavors completely. The next day I rinse them out with hot water again, stuff them with a twisted paper towel to soak the moisture out, then pull...
  13. SilverZero

    RDA's vs Throwaway Drip Atomizers

    Me too, it's just so easy to pull the old cotton out, do a quick dry burn, and add new cotton when changing flavors. I still do have a 510 dripping atty that I bought a few months ago but at this point it's reserved for a specific flavor. I have a chocolate dessert vape that I love but that I...
  14. SilverZero

    Digital Cartomizer / Atomizer Resistance Tester (Ohm Meter)

    In case that link doesn't work for you: https://c2cvaping.3dcartstores.com/Ohm-meter-rechargeable_p_209.html
  15. SilverZero

    Rba problem please help

    On my AGA-T2 the fill hole is on the opposite side of the wick hole. If I tilt it to ensure the wick is saturated I don't get any leaking. :confused:
  16. SilverZero

    AGA-T2 issue with center pin

    True, but on the RSST I think that spring/washer combo have something to push against; on the AGA-T2 the pin will push the bottom insulator up into the tank if you tighten it down on your mod too much. Thanks for the suggestion, I think tomorrow I'll pull it apart and see if I can do some...
  17. SilverZero

    Ohms when wrapping coil? need help!! how to tell ohms if i dont have a an ohm reader

    The length wire that you are using and the resistance of that wire determine the total resistance of the coil. If you are going to be building coils go out and buy a multimeter; you can pick one up for about $15 at Wal-Mart.
  18. SilverZero

    Itaste 134 help

    Does it blink red even when you don't have anything attached to it? If you know the batteries are good and it's doing that then I would guess that it has a major issue. EDIT: Any chance you are putting the batteries in backwards? Just a thought.
  19. SilverZero

    Rba problem please help

    Have you tried keeping the fill hole open? Apparently that helps with wicking issues on Genesis-style atomizers sometimes.
  20. SilverZero

    Need help choosing a new atty

    I'm going to try to buy one of those, I keep hearing great things. The last time I searched for it I found a preorder page that had the price at around $90 I think. EDIT: To crawler95, here's a review video for it that I watched recently in case you want to check it out...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu