Search results

  1. Oktyabr

    New GOTVAPES.com 2nd Multi Mega Prize Monthly CONTEST Giveaway!!!

    Good morning! Wow! I go to bed and some how two resets and a dozen pages slip by in my dream.... That was no dream!!! :shock: As of Tuesday 5/7 @ 11:46 AM Still on Hold--Round #16 Pick 4 numbers from 1601-2000 1612 1772 1854 1952 Please? Thanks! :)
  2. Oktyabr

    What are you waiting for in the mail?

    Sigelei #19 mechanical mod, run number TWO (supposedly Sigelei "fixed" something that they felt was wrong with the first run). So excited! Now just need to figure out what to order to go on top of it... a third AGA-T2? A couple of new drippers? Hmmm....
  3. Oktyabr

    is it okay to mix juice in a tank?

    I did a dessert mix of MBV's "fudge brownie", "peanut butter" and "butterscotch". :) When I'm mixing flavors "in the tank" on my tanks I add what juice I want and then suck *all* the juice back out of the tank into a syringe then pump it back in again. Repeat this a couple of times and juice...
  4. Oktyabr

    Sigelei Mechnical Mods

    vaportekusa and discountvapers both have some sigelei in stock, exhalevapors will soon.
  5. Oktyabr

    To RBA or Not to RBA - Please convince me

    I'm reasonably sure I've seen Phil Busardo vape Boba out of an SS wicked gennie...
  6. Oktyabr

    Sigelei Mechnical Mods

    Yes, as I said maybe a page back that whole switch assembly MUST come apart just so they have a way to assemble it in the first place, right? I don't own any model other than the #8 but I can't imagine the others must be much different. A bit of heat to the button top, then unscrew the button...
  7. Oktyabr

    Sigelei Mechnical Mods

    I wish I could tell you! I went to my local hardware store with a vague image in my mind of what I was looking for. I do this all the time and habitually end up walking out with two or three of several different sizes of everything... all unmarked, in the same bag. Sorry! Take your #8 with...
  8. Oktyabr

    To RBA or Not to RBA - Please convince me

    All depends on how you build and how you maintain it. The wicks should be good for... I'm not sure anyone has ever worn out an SS mesh wick, to the best of my knowledge ;) The coil on the other hand... When I made my first attempt(s) the coil generally had a life expectancy of about 30...
  9. Oktyabr

    To RBA or Not to RBA - Please convince me

    LOL!!! Spoken like a true, hard core vaper ;)
  10. Oktyabr

    Sigelei Mechnical Mods

    Don't know about a replacement spring. I've personally got hopes that some US vendor will be allowed by Sigelei to carry an inventory of spare parts for these but so far no joy. This is my spring/brass screw mod to my #8:
  11. Oktyabr

    Sigelei Mechnical Mods

    No, between the end of the firing pin on the *inside* of the tube. Washers like I used will require the button to come off for full disassembly. This shortens the button's "throw" and also keeps the lock from spinning all the way off as a fringe benefit.
  12. Oktyabr

    Introduction

    Be advised you may need to prepare some lower nicotine juice for those times when you decide to "just take a peek at what's going on over at ECF"! Hours can fly by in an instant! And whole tankfuls of juice mysteriously vanish just as quickly!!! :D
  13. Oktyabr

    Sigelei Mechnical Mods

    Hot off the press for those of you waiting on a #19 from Exhale Vapors:
  14. Oktyabr

    Sigelei Mechnical Mods

    The button on my #8 was very tight, probably assembled with some loctight or similar substance. A little heat to the button and a pair of needle nose pliers on both the firing pin end and one on the button and it twisted right off... the button itself is actually part of a threaded female...
  15. Oktyabr

    To RBA or Not to RBA - Please convince me

    I just slip mine into my pocket all the time. If I'm driving I tend to take it out so it's more readily available but on a few short trips that's just where it stayed... usually in a front pants pocket. No leaks yet and I vape with the "fill screw" out too (it's in my spare parts bag). In a...
  16. Oktyabr

    Victory over aga-t!!!

    Kudos to Kanj.nguyen who not only helped get ME started with RBAs (yeah, I remember) but was kind enough to steer at least a couple of us towards this thread. *subscribed*
  17. Oktyabr

    Victory over aga-t!!!

    I too would very much like a tutorial, video even :D, before I butcher a sheet of mesh... which I'll probably end up doing anyway. So I'm looking at installing in a AGA-T2... will the 3 wick as you spec'd it fit in the stock hole? How large a hole do I need to hit 7 wick nirvana?
  18. Oktyabr

    Sigelei Mechnical Mods

    Hmmm... I can hardly wait to get mine! Where did you find that copper spring? Someone said altsmoke but I've been unable to locate one on their site.
  19. Oktyabr

    To RBA or Not to RBA - Please convince me

    This is very true! I got into RBAs before I got my mech and while I really prefer my SLR stuff (both RBA and drippers) on a mech I have one of my AGAs wrapped for 1.5 ohms so it plays nicely on the Vamo too.
  20. Oktyabr

    To RBA or Not to RBA - Please convince me

    Oh come on you guys!!!! Share a link with a fellow RBA'er!!! I googled "pdibs mesh tubes" and come up with nothing e-cig related. :glare:
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu