Search results

  1. Donovan69

    T3's not seating all the way on ego?

    Face it the threads on t3s are always crunchy when you first thread them down on an ego battery. Likes been said don't over tighten. You may have pushed your post down in your batt or your t3. Watch the vid and try pulling the post. You just need to make a connection. Are they actual T3s by...
  2. Donovan69

    Hi guys! New to site and new to vaping

    Welcome to ECF and I have the vamo v2 and they are a great beginner VV VW device. You get to feel like an advanced vaper!! Sad to say I only use my vamo to check resistance on the atomizers I build. Thats because I am lazy and my multimeter is out by .6. So every time I check the res on...
  3. Donovan69

    Thanks. I am very good friends with Shane. I thought there was someone in Aggasiz. I have a...

    Thanks. I am very good friends with Shane. I thought there was someone in Aggasiz. I have a friend who lives there who just started DIY ing. He is wanting to get his own thing going. I was just wondering if there was somebody out that way. He either gets his juice from me or Shane. Would be...
  4. Donovan69

    Kanger T3S Cleaning advice

    Heres how I do it!! Kanger T3 how to clean you wicks and coils!! - YouTube Or to rewick and coil it... Kanger T3 how to rewick and coil with 2mm Ekowool !!! - YouTube Good luck!!
  5. Donovan69

    Hey there who else from BC

    Would love to know where those guys are!! Pm me!
  6. Donovan69

    Aga T2 Tank is Awesome

    Used to run my ago t+ on my vamo at 1.3 ohms. wasn't bad but I had alot to learn. Now I am using 32awg twisted wire and have virtually never had any problems with hot spots. I was getting hot legs at the bottom then I learned about kinking the wire. I wanna mod my aga with a pen spring and...
  7. Donovan69

    Hey there who else from BC

    Abbotsford here. Get my stuff from BCvapers, ESV and happy vapers. We started VIP Vapes in Abbotsford.
  8. Donovan69

    Dropped Effest IMR 18350

    Well I do know this. The vamo hits ways harder with two stacked 18350s. Pbusardo has some neato graph stuff on his review of the vamo. when I first got mine I loved it using the stacked setup. But when i got my first genny I started running it in shorty mode. I have since started using mechs. My...
  9. Donovan69

    how much difference will a Vamo make?

    I got my vamo a few months ago and I love it!! It is the version 3 with the ego cone threading that accepts evods and kanger t3s. It is an awesome device. The only issue I have had with mine is the 510 threading is a bit wonky. By that I mean my carto tanks and gennys tip Back and forth and side...
  10. Donovan69

    (CLOSED)JUne Giveaway Thursday the 20th starting at 8PM Eastern

    838 thanks need wick n wire :)
  11. Donovan69

    Micro Coils to increase Vapor, flavor & TH

    I have been rewicking T3s with 2mm ekowool. Prolly same on pro tank. Kanger T3 how to rewick and coil with 2mm Ekowool !!! - YouTube Enjoy!
  12. Donovan69

    RSST wont get below 1.8 max

    I make twisted 32g all the time. It slices the resistance in half. Comes out pretty close to 28g. I also notice that I get less hot spots with twisted wire. Mind you I am using 28g on my rsst!! But on my aga t+ and aga-s I am using twisted wire due to the room between my ss wick and the positive...
  13. Donovan69

    RSST wont get below 1.8 max

    I set my rsst up with 400 ss mesh, hollow wick. 28g kanthal 3 wraps came out at .6ohms. Check it out.... Smoktech Rsst .6 ohms!! - YouTube enjoy!!
  14. Donovan69

    E-cigs in the news again.

    Vape bans of any kind suck!
  15. Donovan69

    Aga-t 2 or Rsst?

    I have both the aga t+ version 2 and the agat2 as well as the rsst. My rsst I have had for 2 weeks. It sat on my shelf and mocked me for a week as I tried to figure out how I wanted to build it. My first build I did on it I built dual wicks and coils usin the peter k method with 32 guage twisted...
  16. Donovan69

    Sub ohm build

    I built my igo-s with 32g kanthal dual coils first build... Igo-s dual coils part 2 - YouTube second build... Igo-s part 3 dual coils .5 ohms - YouTube and performance.... Chain vaping the Igo-s (smokeshow) - YouTube
  17. Donovan69

    The IGO-S

    Second rebuild on the igo-s Chain vaping the Igo-s (smokeshow) - YouTube
  18. Donovan69

    dual coil on igo-l QUESTIONS.

    Igo-s part 3 dual coils .5 ohms - YouTube Chain vaping the Igo-s (smokeshow) - YouTube safety first at sub ohm vapes!! Aw imrs can push 10 amps heres a good vid on batts Resistance & Air Flow - YouTube Batteries, Volts, Amps and You - YouTube enjoy!!
  19. Donovan69

    best place to buy bulk rba material in Canada?

    I'm gonna say it again....EKOWOOL ROCKS ESV!!!
  20. Donovan69

    Help on RBA

    Oh yeah and for beginner rba users....get a multimeter and like its been said safety first. I started with an IGO-L and haven't looked back. Now I got an IGO-S...check it out... Igo-s dual coils part 2 - YouTube
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu