Search results

  1. bkkdaytrader

    first nickel build on sx m-class subtank mini rba

    powering and watch the temp it flys around then tops out at 300
  2. bkkdaytrader

    first nickel build on sx m-class subtank mini rba

    yes it is nickel--they repackaged the wire so it does not show the gauge....isnt it supposed to cut out once it gets to 300 degrees --and isnt it suppossed to cut out before any dry hits?? increasing the temp to 400 would still result in dry hits is suppose
  3. bkkdaytrader

    first nickel build on sx m-class subtank mini rba

    8 wraps---2.5 diameter... the wire i got does not specify the gauge-- i would say it is 28 gauge
  4. bkkdaytrader

    first nickel build on sx m-class subtank mini rba

    trying to figure this temp control stuff out so i built a nickel coil==cameout to .121 ohms--maybe one too many wraps set the joules to 19.. temp to 300 degrees seems to work fine but as the juice is running out i am starting to get some harsher hits...this should not happen right?-- getting...
  5. bkkdaytrader

    Get frustrated with rba subtank!

    I've got 3 minis and went straight to the rba--- I use 80vga/20pga and about 5% saline solution I use my stanfdard kf build 28g 2.5 7-8 wraps and use shiseido cotton I follow rip trippers advice to back the wick away from the juice hole and so far have 0 issues---vapes as good or...
  6. bkkdaytrader

    Attack of the (Kayfun v4) Clones!

    thanks for the guidance--i will try it again tomorrow--as its night here in bangkok and I will get some rest
  7. bkkdaytrader

    Attack of the (Kayfun v4) Clones!

    aha--ok can try that--but then how tight to make #9? if i tighten it then cant move the jC ring
  8. bkkdaytrader

    Attack of the (Kayfun v4) Clones!

    getting 510 to screw into #11 is my problem as there is no way to hold #11 as it is sitting inside of # 8 and it just keeps spinning
  9. bkkdaytrader

    Attack of the (Kayfun v4) Clones!

    yes screw #9 was a little loose but when i tighten it then I cant rotate the JC ring.....gurgle and then leak the 510 pin should screw all the way into #11 right? I cant get it to screw and hold the thing together
  10. bkkdaytrader

    Attack of the (Kayfun v4) Clones!

    I'm giving up on this pos for now --i got it all apart now and can't get it back together--the 510 screw wont screw into that little plastic piece my hands area all cut up from screwing and unscrewing sections----
  11. bkkdaytrader

    Attack of the (Kayfun v4) Clones!

    yes the deck includes the chimney where the wick goes--the problem seems to be in the base part below the deck ohms are jumping all over the place also--i just noticed that 1.8 to 2.5
  12. bkkdaytrader

    Attack of the (Kayfun v4) Clones!

    well i take the deck out... then i cant do any thing to that last bottom section. a picture cant show the wobblyness--there is some play between the bottom section and the JC ring......my friend also has on with the same issue. why would airflow increase when I loosen JC? O-ring issue??
  13. bkkdaytrader

    Attack of the (Kayfun v4) Clones!

    I have a Kayfun V4 By Easter thats having problems- --flooded like crazy and JC was extremely hard to turn---that has sort of fixed itself but now it is a little wobbly at the JC ring section-- and basically i can vape with the JC closed all the way--when it gets dry i open the JC and...
  14. bkkdaytrader

    Kanger Subtank...Rough Start, But Nice Ending

    I find that using the rebuildable coil unit i have too close the airhole all the way or else i get dry hits---the juice holes in the coil unit seem to be very small and with my high% vg juice it takes a lot of suction to get the juice through those holes- maybe its a wicking issue but i use the...
  15. bkkdaytrader

    P4U/ IPV3 150w Owners Discussion / A Place to Discuss Concerns and Performance of the IPV3

    Thanks-- What about the red wire that has been partially severed? The white twisted wire is my fault--The 510 connection has a screw that I kept twisting not realizing that it is a spring loaded and should not be screwed---would the twisting cause permanent damage?
  16. bkkdaytrader

    P4U/ IPV3 150w Owners Discussion / A Place to Discuss Concerns and Performance of the IPV3

    my ipv3 started having problems--extremely eratic ohms readings--then it totally failed showing 0 ohms--i opened it up and fired up and it started with the eratic readings again and smoke and electric smell--this is what i have found-- The 510 wire is extremely twisted and the red wire from...
  17. bkkdaytrader

    I just bought the Cloupor T5

    Mine has the same issues as those in your quoted part--hope they get fixed sep 16
  18. bkkdaytrader

    I just bought the Cloupor T5

    all the tech details aside--which are very nice but what I love about it is the form factor--its just nice to hold and vape
  19. bkkdaytrader

    coil build advice

    hi all need some advice on what coil to build for my first real RBA build Ive got 28,26,24 and 21 G kanthal--to be used on a Magma RBA with a IPV2 50 watt device. I want to scale into this a little slowly --so what would be a nice first build to get around .9 to 1.1 ohms.--dual or single...
  20. bkkdaytrader

    Zen ZNA clones coming...

    possible to order minimum 5 units at 60$ each direct from manufacturer these will basically be same dna chip as hana clone--an basically same as hana clone but in zna form factor
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu