Search results

  1. AMDTrucking

    Rayon wick, better flow, flavor, saturation and Nic Hit!

    FYI: This FT Big Dripper (I have the same one that you do) dumped the entire content of the tank onto the deck when I was driving over the hill (4500 Feet altitude). Needless to say that most of the liquid came out of the airflow holes and did the mess. I'm using DIY 70% VG liquids.
  2. AMDTrucking

    Rayon wick, better flow, flavor, saturation and Nic Hit!

    Yes sir. 14 wraps of 26 Ga Ni200 over 3.0mm rod. It looks like yours because... Where do you think I've got the idea of Rayon wicking Flash E-Vapor from? From you of course :toast: My year old Flash-e didn't get much use before. I only used it as my "Experimental Build Guiney Pig Atomizer"...
  3. AMDTrucking

    RDA Magma RDA - lifting of air channels

    And these are the needles: 10, 12, 14 Gauge needles If you don't want to drill those holes, then use 12 Gauge needles. They fit perfectly snug.
  4. AMDTrucking

    RDA Magma RDA - lifting of air channels

    Dremel's cut-off wheel, like butter.
  5. AMDTrucking

    DNA 40, NR, Nickel Builds

    None, what so ever. There is no room to do spaced coil of that size :laugh:
  6. AMDTrucking

    DNA 40, NR, Nickel Builds

    Here is what was wrong with mine: And then, I accidentally put one of the batteries up-side-down and fried it completely. Oops.
  7. AMDTrucking

    RDA Magma RDA - lifting of air channels

    The stock air holes were large enough to house 12 Gauge (2.0mm) hypodermic needles, but I enlarged mines to install 10 Gauge (2.45mm) needles. But your idea is great. Спасибо за идею. Больше не сопливит.. :laugh:
  8. AMDTrucking

    Fogger V4!!

    I'm sorry, I'm off topic again. But I remember some time ago we've talked about Magma RDA and I finally got around to fix it. The stock vertical air holes were large enough to house 2.0mm /12 Gauge hypodermical needles, but I enlarged them for 2.45mm / 10 Gauge ones. As the result, it is dry as...
  9. AMDTrucking

    Post pictures of your working wick and coil setup

    Magma with 10 Gauge (2.5mm) air tubes 0.35Ω 0.9mm X 0.1mm flat ribbon NR-R-NR and trimmed tails Rayon.
  10. AMDTrucking

    DNA 40, NR, Nickel Builds

    Flash E-Vapor
  11. AMDTrucking

    DNA 40, NR, Nickel Builds

    I've got my Vapor Flask back from service and tried 26 Gauge Ni200 coil. It works wonders at 0.1Ω but it is huge. Not every atomizer will have enough room for it.
  12. AMDTrucking

    Rayon wick, better flow, flavor, saturation and Nic Hit!

    I've got my Vapor Flask back from service and tried 26 Gauge Ni200 coil. It works wonders at 0.1Ω but it is huge. Not every atomizer will have enough room for it. Trimmed Rayon wick has no problem supporting this build.
  13. AMDTrucking

    Fogger V4!!

    I've got my Vapor Flask back from service and tried 26 Gauge Ni200 coil. It works wonders at 0.1Ω but it is huge. Not every atomizer will have enough room for it.
  14. AMDTrucking

    Official DNA 40 introduction

    I've got my Vapor Flask back from service and tried 26 Gauge Ni200 coil. It works wonders at 0.1Ω but it is huge. Not every atomizer will have enough room for it.
  15. AMDTrucking

    Rayon wick, better flow, flavor, saturation and Nic Hit!

    I get this on almost every FastTech order. Check this out: Tracking number LN541490109CN
  16. AMDTrucking

    Kayfun LITE

    OK, I just ordered rDNA40 Vapor Shark. I was going to get Kayfun V4 but VapeRev posted this on their site: "Update 12/06/14 10:42am Unfortunately, as a result of unforeseen circumstances, the Kayfun V4 release both in store & online must be postponed. We apologize for any inconvenience this...
  17. AMDTrucking

    Rayon wick, better flow, flavor, saturation and Nic Hit!

    Yes. They received my Vapor Flask on Monday 12/01/14, fixed it and sent it back to me on Thursday 12/04/14. It should be delivered to me on Monday 12/08/14. Also, they responded to every inquiry of mine on the status of the repair via Facebook messaging. So far - so good.
  18. AMDTrucking

    Taifun GT Discusion!

    The diameter of the base is 23mm, then the hole appears to be about 3.5 - 4.0 mm approximately. IMHO
  19. AMDTrucking

    Post pictures of your working wick and coil setup

    Didn't you mean 1mm X 0.08mm Flat Ribbon?
  20. AMDTrucking

    Fogger V4!!

    Your own $30.00 Lemo has 3.1mm Airflow hole which is awesome. (I got me one too :-))
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu