Search results

  1. MattBott

    TFA RY4 help

    I haven't used the standard RY4, but I have been playing with the Double RY4 from TFA. My recipe for it so far is: 10% DRY4 1% EM 0.3% Acetyl Pyrazine 1 drop white vinegar per 5ml Needs a few days of steeping for the AP flavor to "calm down" and about a week total to be a decent vape. Another...
  2. MattBott

    noobie zenesis question

    Where did you buy it from?
  3. MattBott

    Magnetic switch for bottom fore mod

    Check out these guys for magnets as well. I got some from them, but haven't had a chance to use them yet. I plan on using some for the cover of my DNA20 mod (if I ever get the time to build the damn thing). K&J Magnetics - Products
  4. MattBott

    This is not a pipe...

    I'm going to guess that's where the air flow for the genny atty comes from.
  5. MattBott

    This is not a pipe...

    Amazing work!!
  6. MattBott

    510 auto switch mod with ego adapter?

    As long as the ego adapter is unsealed (like this one), it should work fine.
  7. MattBott

    aluminum DNA 20 box

    Good call. Also if you do this, I'd suggest putting the tint on the back side of the plexi so there's no lip where the cut is.
  8. MattBott

    DNA 20 E Pipe

    Amazing work!
  9. MattBott

    The Wizard Labs Thread.

    Putting the EM crystals in a small baggy and crushing them with a spoon helps a lot too.
  10. MattBott

    single 18650 vv/vw bottom feeder

    Your best bet would be to see if anyone makes a DNA based mod bottom feeder. I'm pretty sure I've seen them around, just can't remember where...
  11. MattBott

    Easiest way to start? Buying my wizardlabs nicotine at the same mg as what I vape?

    I vape and DIY 18mg 50/50, so I'll chime in. I choose to go with 36mg VG and 0mg PG. Making 10ml of juice with 20% flavoring (common for a few of my mixes) means 5ml of the 36ml VG, 3ml of 0mg PG and 2ml of flavoring. I decided to go with VG nic instead of PG nic because if I ever want to...
  12. MattBott

    Aga-t+

    Can't wait for the co-ops to start running!
  13. MattBott

    What to do with old batteries?

    Target has battery recycling bins as well. If they don't, you can give them to the guest service team member and tell them to put it in their special handling bin.
  14. MattBott

    Hello for W PA . . .

    You and Yinzer should join us on the Facebook group, Steel City Vapers' Club
  15. MattBott

    ohms jumping all over

    It may take a while of messing around to figure out what's working for you. If you have a hotspot from your wick to your center post, the coil is either too tight, the nut holding your wire to the center post is too tight, your shorting on the wick where the wire first touches it, or the length...
  16. MattBott

    Any good solutions for AGA-T RBA hole line up?

    I can't remember where I saw this suggested, but if your air hole is going PAST your wick, you can take the o-ring off and add a few layers of flat dental floss, then slide the o-ring back on. This will push your o-ring out slightly more and you will get a more snug fit when you have the air...
  17. MattBott

    ohms jumping all over

    Generally if you are using a genny and your ohms aren't steady, you're getting a short.
  18. MattBott

    Tribute to the original Thor's Hammer

    Well done! Since I'm looking for a way to make a top button for a pipe mod I've been planning, would you mind showing / explaining how your button works?
  19. MattBott

    Lexi-DNA20D

    It lists the minimum Atomizer Resistance as 1.0 ohms. Typical 2.5 ohms, Maximum 3.3 ohms.
  20. MattBott

    Sweet Cream?

    I use Sweet Cream at 2.5% in my caramel latte juice to round it out and give it a little bit of a fuller taste.
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu