Search results

  1. BJ43

    JUST TOBACCO, no perfume, no caramel, no vanilla, no tba

    Started cold extracting over 5 years ago. Don't see where everclear would be that much better than 151 proof rum or vodka.:)
  2. BJ43

    Just hemp

    Got some Seacell from a friend.:) Looks a lot like the ramie. Put some in a Taifun GT double 1.10 coil at 17 watts it is vaping great. Very clean flavor. Really liking it. Will do some tests to see how it compares at wicking, but just from the use I can see it is very good. Now to see if it will...
  3. BJ43

    Mike n Tibs DNA Mods!

    Gracias.......
  4. BJ43

    Mike n Tibs DNA Mods!

    So where did I put Baps step by step for the Tibs....:mad:
  5. BJ43

    Just hemp

    A friend sent me some Tencel to try.:)Thanks. I set some up in a Russian 91% and an Igo dripper, both with 1 ohm 28g coils. My first reaction was, this is very good. Very clean flavor. The tencel comes pretty shredded and much more difficult to form into a constant density wick, almost...
  6. BJ43

    IMO, Taifun GT, best RBA.

    For the last few months I have used 6 Taifun GTs almost exclusively, with an occasional dripper thrown in. I am curious to know if someone has found something better. Please don't post if you have not tried a GT, and no gennies or Russian types as i have many of those in the retired drawer. I...
  7. BJ43

    Just Ramie:

    Moderate....
  8. BJ43

    Just Ramie:

    Here is my 1 ohm with ramie after a week of dripping at 20 to 25 watts. I leave the coil higher, not sitting in the ramie so the whole coil can produce vapor. Submerged coil just boils the juice and reduces vapor.
  9. BJ43

    Just Ramie:

    I agree on the soaking. I also start vaping at a lower wattage then after it breaks in, I increase the wattage. I do not have the patience to soak overnight..:)
  10. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    470 ohms ?????
  11. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    Thanks, If I had the talent I would make a 3D box for the raptor with the lipo. My box is larger than needed. Still may make a 3D the old fashion way, cardboard, fiberglass, and carbon fiber. :)
  12. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    I now use this charger that just plugs into 110v and does not need a 12v source. Radio Control Planes, Helicopters, Cars, Boats, FPV and Quadcopters - Hobbyking 
  13. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    It is smaller out of the case. Charged with a balancing charger thru just the balancing plug at 2 amps.
  14. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    4 batteries in the hard case, 2 parallel packs and then those two in series.
  15. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    Three times as much vape time. Very low internal resistance. Only .04v load voltage drop with 1 ohm coil at 23 watts. Radio Control Planes, Helicopters, Cars, Boats, FPV and Quadcopters - Hobbyking.
  16. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    Don't know how much in a week 5 milliAmps will draw but I left mine for 2 weeks while I was on a trip and the 4200 mAh lipo battery went from 3.7v each to below safe (2.5 to 2.8v each). I had to jump start it to get it to charge again.
  17. BJ43

    Show your bottom feed RDAs.

    @B2L, Thanks, very interesting I ordered a couple. I would have never thought of just cutting a channel in the insulator.:)
  18. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    So why do they call it (Idss) when they should of called it (Zgvd). Just to make it more confusing. :) When I get around to it again I will put in a small clicky (snap on off) switch to give me zero drain.
  19. BJ43

    Show your bottom feed RDAs.

    Are you saying you do not have to drill a hole thru the bottom of the pos pin? Are you sure it is copper and not brass? A pic of the inside would be nice..:)
  20. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    Just wire the meter directly to the batteries with a small push button tact switch on either the pos or neg. The switch does not have to be high amp as the meter uses very little current. You can also use a small snap push button switch, stays on or off after each push. These snap switches are...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu