Search results

  1. BJ43

    Show your bottom feed RDAs.

    A7 as a bottom feed: Hemp twine for wick, IGO as a bottom feed with AO wick and hemp feeders.
  2. BJ43

    Show your bottom feed RDAs.

    The IGOs, just drill a hole thru the bottom of the center pin. Then you wrap your pos coil leg on the pos post screw instead of thru the horizontal hole, leaving the horizontal hole in the pos post free for juice to come thru from the bottom. You may have to shorten the pos screw a bit so it...
  3. BJ43

    Just hemp

    Just my personal opinion and the capillary action lab tests I have done. Not taking flavor in account, the following are in order of best wicking: 1 Ramie Top (want to try ramie fiber) 2 Hemp Fiber 3 Bamboo Aunt Lydias 4 Cotton 5 Rayon 6 Linen 7 Jute
  4. BJ43

    Show your bottom feed RDAs.

    I have half a dozen IGOs and a couple A7s drilled out for bottom feeding and am curious what else others have done. Seems strange FT hasn't come out with a bottom feeder.:)
  5. BJ43

    DNAs locking in on OHMs.

    All my Taifuns are firing fine and my floating pin 510s are fine. This is something I now know happens on the DNAs. Since most people change the batteries they just never notice it. Removing the battery resets it and all is fine.
  6. BJ43

    DNAs locking in on OHMs.

    All are Taifun GTs with .8 to 1.2 ohm 28g coils. It has only happened 4 times in the last 6 weeks. Twice on a 20 and twice on separate 30s.
  7. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    Did you build the passthru yet? Luvin my raptor passthru in my truck.:)
  8. BJ43

    DNAs locking in on OHMs.

    Thanks but that is more work than pulling the batteries.:)
  9. BJ43

    DNAs locking in on OHMs.

    All my DNAs 2 (20s) and 3 (30s) tend to lock into a ohms reading and sticking there. If I change the RBA to a different ohm the screen keeps reading the old RBA resistance. The only way I have found to correct this is a hard reset, disconnecting the battery. This is a PITA as all my mods have...
  10. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    I have the voltage meter on battery ground. So far the small Fet is working OK. I have some of these that I may try. Fet Some one else recommended this fet on another thread to be used as a fire switch. I don't understand all the specs so I do not know if it is better than Baps for our use...
  11. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    PSMN1R2-25YLC,115 NXP Semiconductors | Mouser I used this Fet that Bap recommended with the 47K wired just like Baps drawing. Removed the wires from my original switch and soldered them together one (+) goes to the Vin and the other to the zener and the zener is getting the same full voltage...
  12. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    Mine is working as per Baps drawing that seems to be the same as yours. I did not put a kill switch. Since mine is on a lipo I do not have the P-Fet. Vaping it now to see if it quits firing at 6.6V.:) I left the 6.2 zener on pin 5 connected to Vin.
  13. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    Depends on the voltage: At max 6V. .3 ohm is 20 amps 120 watts At min 3.3V, .165 ohm is 20 amps at 66 watts. Don't know why you would want a max resistance but probably around 5 ohms would still produce some vapor at 6V and 7.2 watts.
  14. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    Putting this together I just realized that using this with a push button switch, it is both a master and a fire switch. I can just remove the fire switch I am using and connect the zener directly from Vin to give me LV cutoff.. :)
  15. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    Ditto: My 20 amp 6v raptor is more than I will ever use.:) Fact is the only advantage to me over a DNA 30, is that I can get lower voltage on the raptor.
  16. BJ43

    Okr passthrough

    I built a raptor passthru. http://www.e-cigarette-forum.com/forum/battery-mods/556566-raptor-passthru-my-truck-3.html#post12958800
  17. BJ43

    Raptor Flip-Top VV Mod with 20A, 120W dc/dc converter...

    Switch I am using this 10 amp clicky on my raptor and so far it seems to work fine. Since this is used for a master on and off, there is no gap spark as you are not using it to fire. It should handle 20 amp flow with no problem. The Judco switch is one of the only small push button switches...
  18. BJ43

    Been over 2 years since I've modded, what's new?

    Welcome back. 3D printing is in with high watt DNA boards. http://www.e-cigarette-forum.com/forum/battery-mods/542055-mike-n-tibs-dna-mods.html Or higher amp. http://www.e-cigarette-forum.com/forum/battery-mods/509605-raptor-flip-top-vv-mod-20a-120w-dc-dc-converter.html RBAs: Gennies have...
  19. BJ43

    Just hemp

    Tencel® and lyocell are very similar to cotton in their fire resistance. They will burn easier than hemp or ramie.:)
  20. BJ43

    Just hemp

    Thanks for the link and it is also another source for ramie...:) Louet Ramie Spinning Fiber 7.128 Paradise Fibers
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu