Search results
-
9
How many watts? Can't figure this out
Suggested range... not specific. Sometimes that's a optimal range sometime mechanical safe range and sometime it just numbers sometime it the amount of watts you need to feed. Sent from my SCH-I605 using Tapatalk- 93gc40
- Post #28
- Forum: Coil Builds
-
9
LG HB6s fried my alien?
Batteries don't DRAW amperage.. coils and boards do.... so if anything fried the board it wasn't the batts but it was either the build or users finger. Sent from my SCH-I605 using Tapatalk -
9
Uniform firmware for many devices - ArcticFox + NFirmwareEditor
It on the setting menu. expert. RCOBC y or n Sent from my SCH-I605 using Tapatalk -
9
How many watts? Can't figure this out
I start low and work my way up...... generally I build to run at a specific wattage.. question for me is what combination of wire do I use to get a good vape at desired wattage... only time I Even consider ohm is when building for mech or at extremes of mod output. Sent from my SCH-I605...- 93gc40
- Post #22
- Forum: Coil Builds
-
9
Uniform firmware for many devices - ArcticFox + NFirmwareEditor
Yes I have it on my pico.... no issues yet..... did have similar with earlier versions though. go to AF site or Scan up in the thread. There is a safe mode procedure. Allows for forced FW flashing... might have to go back to Eleaf FW re flash there before upgrading with AF. Sent from... -
9
Voltrove whistle
Any edge or corner between the outside air inlet and the drip tip outlet could produce a whistle. Opening the air a bit will also..... Sent from my SCH-I605 using Tapatalk -
9
Voltrove whistle
Be gentle... likely needs a good polishing more than grinding the edges.... don't forget the drip tip. Changing the bore size might help also. Sent from my SCH-I605 using Tapatalk -
9
Voltrove whistle
Changing the air path might work. But the root of the problem is obstructions in the air path....... now soom are there by design. Ie the coil. Sharp edge on the air holes can also cause whistle.... the smaller that hole gets the more it might whistle. Sent from my SCH-I605 using Tapatalk U -
9
Avocado 22 special edition gunking
Same reason I ordered it...... TC stability...... My worry is I'll need to run more watts with the 26..... I hate changing batteries.... Sent from my SCH-I605 using Tapatalk -
9
Avocado 22 special edition gunking
You might try modeling builds on steam-engine.org. ... I shoot for a Heat flux of 170 to 200 and capacity as close to yellow as I can get. I generally vape at 20watts or less. FWIW I JUST ORDERED A SPOOL OF 26 WIRE....first wire other than some clapton I have bought or used heavier than 28... -
9
Avocado 22 special edition gunking
26awg 316 @ 16watts I'd probably build at around .4 to .5 so 6 to 7 wraps on 2.5mm. Sent from my SCH-I605 using Tapatalk -
9
Avocado 22 special edition gunking
Actually most gunk form while the coil is heating up and cooling down.... lower watts don't let coil get hot as fast and big coil cool slowly. A faster coil would help... what mod are you using do you have preheat? Sent from my SCH-I605 using Tapatalk -
9
Coil Master COMP WIRE
Comp wire is an OLD brand name. When introduced it was the state of the art. As the only other cloud wire was nichrome.... the craziest of chasers of the time we're barely building as low as .5ohm for them massive clouds..... on a mech with stacked 18350 or 18500 batteries...... Sent from my...- 93gc40
- Post #5
- Forum: Coil Builds
-
9
RDA Looking for a Hybrid Dripper!
You want an atty with a protruding 510 pin. The further it protrudes past the threads the better. Sent from my SCH-I605 using Tapatalk -
9
Avocado 22 special edition gunking
Low wattage big coils and dark juice....... equals faster gunking... Fwiw those look broke in to me... when my coils gunk you can't see wraps anymore. Sent from my SCH-I605 using Tapatalk -
9
Voltrove whistle
That happens...... you might reduce it some if you remove all sharp edges in the air path..... Sent from my SCH-I605 using Tapatalk -
9
Please HELP ME
Replace any bad orings and get the wicking correct... that's how you fix a leaky tank. Sent from my SCH-I605 using Tapatalk -
9
Ohms drop
Loose connections often read high....... Sent from my SCH-I605 using Tapatalk- 93gc40
- Post #6
- Forum: Coil Builds
-
9
Ohms drop
Normally ohm rises with usage.... Make sure all you contsct are tight and no coils are touch what they shouldn't. If it stable and I like the vape.... I'd just vape it.. But... WHEN IN DOUBT THROUGH IT OUT.... doesn't just apply to batteries. Sent from my SCH-I605 using Tapatalk- 93gc40
- Post #2
- Forum: Coil Builds
-
9
The Best Mod to get that lasts, inexpensive to maintain...?
Yeah I got the bad eyesight thing..... But you ask what the solution to having to replace your coil every 2 days was........ Fwiw... I know a BLIND from birth vaper that DIY his coils and juices..... I figure someone with bad eyesight could use a magnifier. I build using a jewelers loop...