Search results
-
9
Can't figure out my own coils
Ok try 8 wraps of either on a 3mm core..... start with the mod set to about 15watts..... With either of those wires to get performance like the clapton you will need to build kinda on the higher ohm side or go with multi wire or multi coil builds. Sent from my SCH-I605 using Tapatalk- 93gc40
- Post #5
- Forum: Coil Builds
-
9
Tfv12 coils longlivity - rough estimates
Depends on power and juice longevity should be from 1 day to a month or so for the wick and 1 day to multi years on the coil. Just like any coilhead or build. Sent from my SCH-I605 using Tapatalk- 93gc40
- Post #2
- Forum: Tanks and Replaceable Coils
-
9
Can't figure out my own coils
Are you using a coil calculator like Vape tool or steam-engine? VT is easy and Steam will help understand. We can't help without knowing what you want and what you have to work with to get there. Sent from my SCH-I605 using Tapatalk- 93gc40
- Post #3
- Forum: Coil Builds
-
9
Kayfun lite polish
The only authentic Kayfun I have seen..in person... was what I would call a sand blasted finish.. I guess you could call it satin.. online I have only seen polished versions and brushed. Sent from my SCH-I605 using Tapatalk -
9
Ehpro Kayfun lite plus V2 leaking issues
You need to use a needle to fill through the bottom... can be done with regular dropper but more messy. I bottom fill my kayfuns... it's just easier. I use KFL and a 3.1..... 3.1 being side filled.. must use plastic needle bottle on that one..... top gill work once you get the hang of... -
9
Ehpro Kayfun lite plus V2 leaking issues
Also if the coil is too low the wick can siphon juice down the air hole.. note a drop or two out the air hole isn't a leak.. that's condensation buildup and draining. If you are top filling.. start threads then flip tank over to screw top on..... this will force excess air out of the tank... -
9
Ehpro Kayfun lite plus V2 leaking issues
And don't. Over tighten the segments.... this will also cause o ring issues. How are you filling the tank? Describe or put photo of you build and wicking. I cut my wick so that they just brush the deck over the channels. Sent from my SCH-I605 using Tapatalk -
9
Can a borosilicate glass tube be cut in order to make a new tank tube?
Your going to need a diamond grinding wheel to flatten out the cut.. no way your going to freehand a clean cut.... Going to be easier and cheaper to just buy the pieces you need. Sent from my SCH-I605 using Tapatalk -
9
Uniform firmware for many devices - ArcticFox + NFirmwareEditor
This assumes you are already getting a good vape in TC.... what if you are getting a good vape in VW using a self created curve...... and you find that those settings don't translate to TC. At least as far as you have found..... Wouldn't it be nice to see temp wise on the graph what you VW... -
9
Uniform firmware for many devices - ArcticFox + NFirmwareEditor
I'd like to be able to see temp in VW mode when using Device Monitor. .... be nice displayed on the mod too. Sent from my SCH-I605 using Tapatalk -
9
Uniform firmware for many devices - ArcticFox + NFirmwareEditor
I can't tell if the PI settings do anything on the Pico so far..... could be I have just not found the right build for TC yet..... or the right settings. Sent from my SCH-I605 using Tapatalk -
9
Uniform firmware for many devices - ArcticFox + NFirmwareEditor
Thats why I've kept it.. TC just isn't working for me. I also think the Eleaf FW is a bit smoother. But the VW control with the AF firmware is much better than the Eleaf.. the Power Curves allow me to control the vape temp the way I want TC to do it. SO I have 1 TC profile to keep trying... -
9
Uniform firmware for many devices - ArcticFox + NFirmwareEditor
1. No all in one place documentation I have found.... at this point I think they expect users are already familiar with these functions. 2. Don't need or want clock on my mod.. so don't use. 3. Yes. 4. Don't think presets have anything to do with wattage...... I thought it was just... -
9
I would like some help!
What is the coil? What is the atomizer? Mod mode? Sent from my SCH-I605 using Tapatalk -
9
Does anyone else wish more mods looked high end?
No I don't need bling... or to proclaim my social status, to the world..... A simple black or brushed metal box is fine for me.. although I prefer more ergonomic shaping.... Fact Is the guts and function of the mod are much more important to me than looks. Solid gold and diamond incrusted... -
9
Squape x ....SJMY vs Shenray?
When I am choosing between two clones.. and I can't see any real difference I flip a coin or buy the cheaper one. If both are available via fasttech I Will read the reviews there. Sent from my SCH-I605 using Tapatalk -
9
Uniform firmware for many devices - ArcticFox + NFirmwareEditor
On the NFE page I think had a device list...... believe it does TFR with all compatible devices. Sent from my SCH-I605 using Tapatalk -
9
Uniform firmware for many devices - ArcticFox + NFirmwareEditor
No vari_volt....... you can display vape voltage... use that to set watts. Really for most mods this doesn't add features..... it really just ads adjustabilty to existing features. I guess it gives you TCR or TFR if you mod doesn't have them. Both those aren't new features just different... -
9
Uniform firmware for many devices - ArcticFox + NFirmwareEditor
Have been saving for every wire type. When I change the build I look v to see if I have a file for that wire combination. Load it most of my preferences will already be set. Sent from my SCH-I605 using Tapatalk -
9
Uniform firmware for many devices - ArcticFox + NFirmwareEditor
There are 8 of the each is independently programable...... say you have 8 atties with eight different builds... you could set up 8 smart profiles. So that when you attach one the mod automatically switches to that profile.. or like I do shut off the smart feature.. and disable unused...