Search results

  1. atroph

    WISMEC Reuleaux RX200 TC

    TC mods don't assume cold resistance @ 70F. It knows what ambient is and assumes that the coil is the same temp when installed and presumably locked. If not locked the resistance will actually decrease if the ambient temp reads colder and it detects a lower resistance. (assuming that the mod is...
  2. atroph

    WISMEC Reuleaux RX200 TC

    Nope it is internal temp dependant to the mod only and not the coil resistance. This internal temp is the reference that the mod uses to calculate how much ohms increase is needed to reach target temps. I usually lock my resistance once it has settled to its lowest point +/-0.01 ohm. Last...
  3. atroph

    WISMEC Reuleaux RX200 TC

    Odd. It may be the wicking or airflow (not familiar with the mako). I have used ni200 exclusively (3mm 8 wrap 28G .13-.12 ohms velocity RDA) on my RX and always get a great vape between 400-500F at 50W depending on my juice viscosity. I use the stock ni mode too. I have experienced where if...
  4. atroph

    WISMEC Reuleaux RX200 TC

    And here is how it probably is in real life: The 10kohm resistor is there to make the circuit. In reality the load (10k resistor) is variable depending on what you have dialed up.
  5. atroph

    WISMEC Reuleaux RX200 TC

    Here is the three resistor voltage divider circuit example: I used this to make the circuit: Circuit Simulator Applet
  6. atroph

    WISMEC Reuleaux RX200 TC

    I think you are correct. I have not personally seen the inside of the board and wiring other than the pics above. We are both thinking correctly, just different methods. If it is indeed wired like you say then yes an equal resistor voltage divider with say 3 1kohm resistors should do the...
  7. atroph

    WISMEC Reuleaux RX200 TC

    In this case it doesn't matter what the board sees as long as it is within tolerance. Easiest thing is to tap all three wires at vout and they will all be the same 4.2v. Another wire from power supply + to b+ and power supply negative to b- for the high current run that actually drives the...
  8. atroph

    WISMEC Reuleaux RX200 TC

    You will need a voltage divider to fool the battery monitors. It will take two resistors as shown below: The formula and online calculator are found here: Voltage Dividers - learn.sparkfun.com Here is what I'd recommend to keep the current to a minimum. Sent from my 0PJA2 using Tapatalk
  9. atroph

    Joyetech Evic VT 60 Watt

    I depends on your needs. Me personally I would HIGHLY suggest a mod with firmware upgradeability like the mini.
  10. atroph

    WISMEC Reuleaux RX200 TC

    Why would you jump a diode with a wire or solder blob?
  11. atroph

    The Flavor Apprentice Flavoring Thread

    Webview will show signature line. Sent from my 0PJA2 using Tapatalk
  12. atroph

    WISMEC Reuleaux RX200 TC

    Yup you are right. Sometimes the maths gets the better of me. :) fixed post. Sent from my 0PJA2 using Tapatalk
  13. atroph

    WISMEC Reuleaux RX200 TC

    ?? Dunno. So many variables and skill levels of said youtube stars. I would venture to say that statistically speaking this is a great mod. 5, 10, or 50 negative reviews have very little influence on the amount that were sold. 50 bad out of, say, 10,000 is 99.5% success. Ask any business...
  14. atroph

    WISMEC Reuleaux RX200 TC

    Ideally all batteries should be discharged equally in series. Once they age it is possible that on or more may increase their internal resistances. Once this happens it will be strssed less than the others and the ones with lower internal resistances (most ideal condition) will have to bear the...
  15. atroph

    Boring Contest !!!

  16. atroph

    WISMEC Reuleaux RX200 TC

    Yes
  17. atroph

    WISMEC Reuleaux RX200 TC

    Maybe it depends on the meter? I do electrical stuff for a living so I usually have or have access to better tools than most do. Personally I was surprised too that they were that close. The numbers were written in no particular order but do seem to correlate with each other. I have seen on...
  18. atroph

    WISMEC Reuleaux RX200 TC

    I have plenty :) Here are the charges in random order unless someone knows which cell correlates to what is on the screen: (Fluke 87 IV DMM) MOD: 3.93, 3.95, 3.91 DMM: 3.915, 3.942, 3.911 Looks like they are really close to me.
  19. atroph

    WISMEC Reuleaux RX200 TC

    I don't have a Windows machine handy, but I believe it is 1.04 on the latest firmware. Batteries were purchased at the same time LGHG2's.
  20. atroph

    WISMEC Reuleaux RX200 TC

    I've been USB charging since I opened the mod on Dec25. Not a single issue, and the batteries are usually within 0.05 of each other. Sent from my 0PJA2 using Tapatalk
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu