Search results

  1. atroph

    WISMEC Reuleaux RX200 TC

    I upped mine to 0610 and it warms it up better for me. Seems as if my builds settle out really low and prior to 3.0 update I was locking in about 0.1 ohm higher (by heating and removing and allowing it to cool slightly) to get the vape that I wanted. Now I have m1 set at 0610.
  2. atroph

    WISMEC Reuleaux RX200 TC

    Turn unit off. Press fire and up (hold until you see tcr settings). You should now enter the mode to set the TC. It is rather simple from there Fire button is toggle and up/dn are what they should be. Not sure how to lock in. Just let it be? or Turn it back on with 5 clicks. Edit: 5 clicks to...
  3. atroph

    WISMEC Reuleaux RX200 TC

    F-YEAH! Just made morning. Sent from my 0PJA2 using Tapatalk
  4. atroph

    WISMEC Reuleaux RX200 TC

    Ok that helps. Dunno then. Does it do it with all builds/attys? Could be a faulty connection. You said you downgraded to 1.07. Was the problem on 1.08 and not on 1.07?
  5. atroph

    The Flavor Apprentice Flavoring Thread

    Yup ^ I don't think I have a mix that I have tried that isn't shake and vape for the most part. However some DO get better the longer they sit.
  6. atroph

    WISMEC Reuleaux RX200 TC

    It will kick out of TC if your build at any time goes above 1 ohm I believe. Try dropping the resistance (ohms) of your build.
  7. atroph

    WISMEC Reuleaux RX200 TC

    Unkamen seems to be a good vendor for various wires. SS430 and Ti especially. Sent from my 0PJA2 using Tapatalk
  8. atroph

    The Flavor Apprentice Flavoring Thread

    Sounds good! Strange things happen and with that much crud it may be hard to tell what the true culprit is. Sent from my 0PJA2 using Tapatalk
  9. atroph

    The Flavor Apprentice Flavoring Thread

    Jan if your resistance did indeed jump that high I'd suspect a bad connection with either the screws to coil or the 510. No matter how funky your build gets it should not jump resistance. Well, ideally of course. In my short time of vaping I have not seen this happen, or experienced it myself...
  10. atroph

    The Flavor Apprentice Flavoring Thread

    Twisted is notorious for capturing the funk. Once it starts it just cascades until your build is toast. I usually stick with single coil builds that are spaced. If the coil gets crusted on the outside it is usually isolated to just the skinny coil section itself and doesn't propogate to its...
  11. atroph

    Rayon Wick - Better Flow, Flavor, Longevity, and Nic Hit!! - Pt.2

    I think they may be better for flavor, but the wicking can be a little tricky. Either way it is fun to experiment and see what works for you. Sent from my 0PJA2 using Tapatalk
  12. atroph

    Rayon Wick - Better Flow, Flavor, Longevity, and Nic Hit!! - Pt.2

    See above. I edited my post with a added pic of a simple horizontal build. Trolldragon's above is a vertical build (dual) Sent from my 0PJA2 using Tapatalk
  13. atroph

    Rayon Wick - Better Flow, Flavor, Longevity, and Nic Hit!! - Pt.2

    I think you are OK. You configuration is a little different than the standard horizontal coil. Standard horizontals seem to self clean if they are not touching the chamber top or walls. I don't know where the darkness goes, but i do know that if the wick is isolated it will remain clean for a...
  14. atroph

    WISMEC Reuleaux RX200 TC

    Sitting at 3.77 3.81 and 3.87 after a 4-5 hour USB charge last night. Looks like a 0.1 max variance this time. I don't think that is a problem in may case.
  15. atroph

    WISMEC Reuleaux RX200 TC

    As for the firmwares I think we'll have to wait for the RX200 specific one as it has 3x18650 versus the 2 and 1 models with TCR. Me thinks the circuitry inside is completely different (at a minimum how the batteries are wired and recognized by the board).
  16. atroph

    WISMEC Reuleaux RX200 TC

    Most variance I have seen is 0.09v. Most of the time one or the other is about 0.05 off. Two seem to be really close all the time with each other. Honestly hundreth(s) of a volt is nothing to worry about. 0.7 though is a little more worrisome. Right now I am at 3.44 3.45 and 3.50 at the tail...
  17. atroph

    WISMEC Reuleaux RX200 TC

    None here. USB charged since day 1. Sent from my 0PJA2 using Tapatalk
  18. atroph

    Joyetech Evic VT 60 Watt

    I doubt it. They missed the mark with no firmware upgrade-ability. Now that this thing is on clearance I don't really foresee a revival. IMO the internal battery turned people off. To me it was awesome with about 3 days between charges. I'd like to be proven wrong though!! Sent from my 0PJA2...
  19. atroph

    Joyetech Evic VT 60 Watt

    Code didn't seem to work.
  20. atroph

    The Flavor Apprentice Flavoring Thread

    I think it is a community driven percentage average.
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu