Search results
-
Polishing ultem cap
did this back a couple months ago, turned out alright, 2500 grit wet sand, and some jewelers rogue which added no taste or smell to the ultem, unfortunately next to impossible to do the interior. Still an improvement to me. Going to try some tanks next time I have a chance. -
Uniform firmware for many devices - ArcticFox + NFirmwareEditor
I should have said when you select a profile, +-, 3 clicks gets me to select profile +- zeroes stored. Option is shown in text on screen at that point -
Uniform firmware for many devices - ArcticFox + NFirmwareEditor
When your in a specific profile push and hold + - it zeroes stored resistance, I believe there is also a shortcut to do the same thing but cannot recall it off hand. -
Amazing and Not So Amazing Mech Mod Clones
Sounds like time to give the switch a good deep clean. Mine has never heated even with some extremely low builds. Give it a good visual inspection look if you see any build up from arcing. -
Need help with broadside mod
I kind of realize after reading through what I posted may be a little confusing. The basic problem is the Delrin ring which holds the battery adjustment/clutch pin is a bit thin, this allows the ring to be set to deeply into the mod. So the rattle adjustment pin ends up turned out to far which...- ccwaters
- Post #15
- Forum: New Members: Introduce Yourself!
-
Need help with broadside mod
There are two versions of the Broadsides clone, sounds like you got the worse of the two, now its not a bad mod, fit and finish was good on the one I had. However it had the same issue your experiencing. the fix is not difficult, but it may take a little messing around. The problem with it is...- ccwaters
- Post #14
- Forum: New Members: Introduce Yourself!
-
Coppervape's Skyline Clone
only Coppervape that I've seen so far, SXK has it added to a couple listings on alibaba for search engine hits, but no one else I've seen so far. Marvery had it listed on DHGate, but they are just a reseller not a manufacturer. -
Amazing and Not So Amazing Mech Mod Clones
No clear coat internally on anything I've gotten so far, exterior yes, inside no. Haven't used the brass rda yet, copper and stainless I use regularly. If someone sent them an 11:11, or V2 switch they'd probably update it, otherwise I expect it will ride out with what it is now. -
Amazing and Not So Amazing Mech Mod Clones
Good job, they definitely clean up nicely! -
Amazing and Not So Amazing Mech Mod Clones
Yea, no kidding, 2 days from China to my door, well add a few hours of the third day. If it weren't for customs could knock most of a day off the total. Looks like the package will be here in the morning :banana: -
Taifun GT Discusion!
My airflow requirements are beyond what the Skyline is able to meet even without any insert at all, and once you open it up that much it is lacking in flavor. +limited build space. I tried it mostly due to the huge amount of hype. Yes it a nicely designed atomizer, looks nice, good vape, but... -
Coppervape's Skyline Clone
Not going to get into a debate on something that is completely unable to be proven one way or the other, 800+ orders from FT, my experience does not support it. Besides that has little to do with FT policy on logos. -
Coppervape's Skyline Clone
Incorrect, due to major whining of a select few Fasttech forum members a couple years back FT's policy is to now order clones without logos if possible, not all manufacturers will comply. The logo-less clones from FT are the same quality as those with logo. 3F, Gearbest, 2Fdeal and any other... -
Amazing and Not So Amazing Mech Mod Clones
Technically no, the authentic copper uses V2 switch, but both the copper and brass Kindbright XXX are identical. Have both, and like them. I have Copper, Brass, and Titanium Admirals inbound, they cleared customs in Ohio a bit ago, and might be here this week. -
Amazing and Not So Amazing Mech Mod Clones
as for the inner sleeve, I presume you mean the Pom (plastic) one. It comes out, just a bit of a tight fit. I'll also mention both the brass and stainless versions shipped with copper and stainless switch housings. Not sure why, and which one they'll settle on. But have received brass with... -
Amazing and Not So Amazing Mech Mod Clones
A little polish and or lube smooths the switch as does use, one of mine had a little burring on the slots in the switch which caused a little crunchy feel. The one you have that does not lock properly is due to Kindbright making the spring too long on the latest batch, it also makes the switch... -
Taifun GT Discusion!
Interesting, mine is just slightly lees then full height and does much better then a reduced height I did try about 1/2 and 3/4, the shorter I got the less I liked the performance, flavor fell off as did density of the vapor. Using cotton in mine is a bit of a balancing act, a little too much... -
Reload Rta
Of the six I got one ended up with some leaking at the base of the tank. others were fine and clean (no stink). Seems as though the bottom ring which retains the o-ring was cut slightly deeper as changing the o-ring with other same size 1x23 didn't help. Digging through my o-ring collection... -
What Mech ya sportin today ?
I was going to say all your numbers seem way high. read the email notices before coming here, lol. -
Taifun GT Discusion!
Yeah, Skyline was OK, but just not for me, had and sold 3 of them. But yea, it may take them a while to put out a BT, or maybe they may pass on it. Seems not all that much enthusiasm over the BT. As long as Shenray doesn't screw it up it will probably be the one to get. Everyone on Facebook...