Search results

  1. Capt' Brian

    [CLOSED BUSINESS]

    Ahoy all, happy Wednesday! I have maybe 150ml of juice before I run out. I used to buy and mix about 600ml at a time and just order when it got low. I also have vaped a 20% cinnamon into menthol mix for years as well too and I've always used the PG80 juice. So I guess, from what I've read so...
  2. Capt' Brian

    [CLOSED BUSINESS]

    I guess I've been vaping around 18 to 24 mg for years due to the ... hmm... "adequate" vapor I was getting from pre-made 2.5 ohm coils I was used to using. I needed it that high to not have cravings. Since I finally ventured into the realm of coil building, sub-ohm vaping and higher watts I'm...
  3. Capt' Brian

    [CLOSED BUSINESS]

    Ahoy! I just finished the first of the Marauder Mark 3's and needed to test the electronics. As the screw on voltage meter won't reach down into the tank well I just screwed on my Phoenix and gave it a vape...... WOW! The Phoenix is a dual coil at half an ohm and I hit it with a fresh 18650...
  4. Capt' Brian

    [CLOSED BUSINESS]

    Yes it would, but I would do it at a minimal cost to basically just cover return shipping. Next time I might try to incorporate some kind of fuse holder, but those things take up even more room inside. arrr
  5. Capt' Brian

    [CLOSED BUSINESS]

    Ahoy! I think we are going to call you "Big-K", arrr!
  6. Capt' Brian

    [CLOSED BUSINESS]

    Yea, I'll try to remember to do it this weekend, just grab a random post I suppose and see if anyone is paying attention to the thread anymore! Here are a few pics of the prototype. It showed me a couple things I needed to change, but it still will function just perfectly for someone...
  7. Capt' Brian

    [CLOSED BUSINESS]

    Thanks! Every mod in the batch is pretty exotic except for the prototype (maybe I should do a random thread give away next weekend). The prototype is African Mahogany as I didn't want to risk a high end wood when I made the first one.
  8. Capt' Brian

    [CLOSED BUSINESS]

    Ahoy! Dead but not forgotten! I've actually been working, just kinda enjoying the quiet for a while. Summers are always slow anyways ... I've taken my time to figure out how to build the Cruiser Mark 3, lots of little details that needed to be addressed. I went with the standard 3034 Mosfet...
  9. Capt' Brian

    [CLOSED BUSINESS]

    Ahh, nice. Then I think it is gonna go on my wish list. Tks for posting!
  10. Capt' Brian

    [CLOSED BUSINESS]

    Man, that one has a big-... drip tip on it, like some others I've seen. I don't suppose a 510 drip tip could wiggle into the opening? I do like the post setup though, nice and wide and easy to setup. ------ On a side note, I've been experimenting with different coil builds and have kinda...
  11. Capt' Brian

    [CLOSED BUSINESS]

    Velocity RDA Bottom Feed 510 Pin - Eciggity
  12. Capt' Brian

    [CLOSED BUSINESS]

    Found 44 hobo at FastTech - Worldwide Free Shipping
  13. Capt' Brian

    [CLOSED BUSINESS]

    I like the looks of that Velocity, I had not noticed it before. I might order one next time I use FT. You think it would be possible to just grind a thin feed slot along the length of the center screw? Found 10 velocity mini at FastTech - Worldwide Free Shipping
  14. Capt' Brian

    [CLOSED BUSINESS]

    Ahoy! Is everyone having a good Labor day? Hope so! Yet another rainy day here in central Florida ... will it never end?? I'm doing paperwork today and finally got that Destroyer40 on the website and also put the few Mods I have available on sale for today. Also, here is a little post to...
  15. Capt' Brian

    [CLOSED BUSINESS]

    It would be possible, but I would not recommend it I think. Also, what do you think about the bad press that the nickle wire used for TC has been getting? I think it may be a real concern if what they are saying is right. I dunno ... I have two mods I'm using right now, main and backup. My...
  16. Capt' Brian

    [CLOSED BUSINESS]

    Ahoy all! I hope everyone is having a bit of fun this summer? I'm getting SOME work done in the shop, but I'm spread so thin with so many things to do that I couldn't even guess when the next batch will be done. Your 26650 mod, is the atty inset hole enclosed or is there a open spot where...
  17. Capt' Brian

    [CLOSED BUSINESS]

    Noooo... no wake up ... DB, tell me a stoooory .........
  18. Capt' Brian

    [CLOSED BUSINESS]

    Shhhhh... the threads trying to sleep .......
  19. Capt' Brian

    [CLOSED BUSINESS]

    Yeah, I think so too. People who know about RSM mods kinda know what I make and don't make. I will try to adapt to the current market as I've always done, but there is a limit. Sometimes that limit is my skill in making mods, sometimes for other reasons. I'll just keep trying to make the...
  20. Capt' Brian

    [CLOSED BUSINESS]

    I have been keeping track of trends and I am aware of what people are doing, but, I think that the sub-ohm trend has gone a step too far, several steps even. Perhaps people are just not aware of the potential hazards that they are embracing (next to their faces). If it means I lose sales and...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu