Search results

  1. Lova

    A bit annoyed: vaping indoors all of a sudden upset ONE coworker

    I understand that, but do most of the people seeing you vape understand that? Also, mainstream media has got it's hold on vaping, so more and more people look at vaping being dangerous for them, no matter what you say or show them. Vaping where smoking isn't allowed is just adding fuel to the...
  2. Lova

    Best "smallish" battery for Atlantis that's NOT an eLeaf iStick?

    If you plan on using it under 30W, you could check out the Mini Volt by Council of Vapor, costs about $40 and is absolutely tiny: Mini Volt Box Mod Council Of Vapor - Vapor Hub
  3. Lova

    A bit annoyed: vaping indoors all of a sudden upset ONE coworker

    Rant: Well this thread took a turn for the worse. Myself, being vaping for about 4 or so years already, don't want to see anyone vaping in a place where smoking isn't allowed without explicit allowance to do so. It makes you guys, who vape wherever you go look like .......s, which in turn makes...
  4. Lova

    E-cig making me cough

    Hello, and welcome to ECF! What you are feeling is most likely adaptation to vaping instead of smoking. The vapor produced by an ecig is more dense than cigarette smoke (some people say it feels like inhaling water into your lungs) and it doesn't contain anasthetical properties or chemicals in...
  5. Lova

    DIY: MAX VG: Should vinegar be used for safety?

    If you're working with fruity flavors, you could use something like TPA Sour (malic acid) or just plain citric acid dissolved into VG and add that to your liquids. As far as bacteria goes, I highly doubt you will get much if at all contamination in your liquids. I personally wouldn't really...
  6. Lova

    Stainless Steel Coils?

    Just make sure you have non-coated stainless steel when building coils! More info below: Haven't made any specifically for the kangertech RBA plus, but I have used Stainless steel for coils quite a many times. Just keep the build above the mod's lowest firing resistance and be sure to use good...
  7. Lova

    Mod maintenance?

    Hello, and welcome to ECF! First of all, if the Homh Wrecker is a regulated mod, which I believe it is, then the only "maintenance" you have to do, is keep the tank/dripper finger tight, no need to pop a vein cranking a tank on the mod and keeping the 510-connector clean, as many have stated...
  8. Lova

    New (again) member looking for advice on hardware :)

    I've only heard praise from those tanks and mods you've picked, I haven't used anything except a iPV3 Li, couple of handmade mods and mechmods personally, so I don't personally know what the Cuboid will be like. As far as tanks go, nobody likes them all. I personally love my modded Bellus and...
  9. Lova

    Problems with my Kanger Subox Mini Kit and Looper Juice

    Hey there, and welcome to ECF! About your issue, did you try shaking the bottles, as some of my homemade liquids tend to leave some of the flavorings on top of the VG/PG and shaking usually mixes them around quite well. Also, as far as cotton goes, if you have a pharmacy or something close by...
  10. Lova

    Main difference between Kanger SSOCC and Clapton SSOCC's?

    Wherever I looked, it was stated that the SSOCC coils use stainless steel wire. Also, what material were the old square ones then, if those casings weren't made out of stainless steel? Do you have a link where it says that the wire inside a SSOCC 0.5ohm coil is Kanthal?
  11. Lova

    Non Smoker wants vape set up for my non smoking home

    I would suggest something like iStick Basics or Joyetech eGrip Oleds and few different flavors. Easy to use and you can use premade coilheads. Also, those two are most preferred for smokers who want to vape due to tighter draw and not that much vapor. Also, if you aren't a vaper yourself, I do...
  12. Lova

    Reo Lounge Part VI

    It depends massively on the build you put in it though. The build in the pic I posted doesn't really have any spitback, but if you build the coils closer to the center of the deck and away from the airflow holes, you will get massive amounts of spitback :)
  13. Lova

    Reo Lounge Part VI

    You could try. There would be almost no airflow and it would be prone to leaking due to wicking method used in a coil like that. Also, the driptip has got a plastic mesh "spitback guard" which would melt if the coil is too close to it. I tried once, it shot hot liquid directly into my mouth, and...
  14. Lova

    Reo Lounge Part VI

    It's definitely different breed of drippers. Deck is extremely cramped, so I don't think you can fit coils larger than 2.5mm ID and 7-8 wraps. Wicking is pretty much threading the needle with the dripper. Airflow is massive, about 1.5mm by 8mm on both sides, really really open airflow so easy...
  15. Lova

    Picture of Your Setup Part 2!

    Yessir, it collects literally milliliters of liquid inside the driptip just due to the tiniest possible space between the driptip and the coils. Imagine a Derringer, but about 3mm shorter and a driptip that covers 80% of the topcap :'D
  16. Lova

    Reo Roll Call

    New Reonaut here. Got my Reo Grand LP a month or so back. My Reo currently resides in far far far up north, Finland and Raahe to be exact. It usually travels between Raahe and Rovaniemi whenever I go to Rovaniemi :)
  17. Lova

    Reo Lounge Part VI

    I'm actually using a LowPro RDA as the topper, I do have a reomizer as a backup, but using the LowPro is what I prefer, not too closed off as the reomizer is :)
  18. Lova

    Picture of Your Setup Part 2!

    No problem, glad I could help :) Edit: Oh right, forgot totally about Le Magister :D
  19. Lova

    Picture of Your Setup Part 2!

    Out of all of the suggestions I made, Rogue and Ax1 are both RDA's that you can't get to leak no matter what you do. Unless, of course, you pour literally 20ml of liquid in the RDA's :D
  20. Lova

    Picture of Your Setup Part 2!

    Give me couple of mins, I'll clean it up a bit and pop the topcap off. Modding my bellus currently haha! Edit: I build it as close to the airflow holes as possible to eliminate some of the spitback, also I removed the plastic grill from the driptip
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu