Search results

  1. squeeze

    How to bulid a BiC Lighter Mod

    I asked Please do not post to this thread
  2. squeeze

    How to bulid a BiC Lighter Mod

    I am working on it Got the pics on flickr now if i could get them on here.
  3. squeeze

    Questions for building BiC mod

    I will only answer questions here on this thread for the BiC lighter mod.
  4. squeeze

    How to bulid a BiC Lighter Mod

    I will stop here for now i need to post some pics so you all know what i am talking about. Can some one tell me how to add pics to this post. Please send me a pm telling me how. Then we can get on to the fun part of building this mod. Please do not post to this thread i want it to be clean. And...
  5. squeeze

    How to bulid a BiC Lighter Mod

    The switch. I used a small tact switch and had to make a plastic mounting plate/shelf to fit inside the lighter. Then i soldered on leads to switch then glued the switch with hot glue to the mounting plate. And had to put leads on the atty connector. Now all the parts are ready for building the mod.
  6. squeeze

    How to bulid a BiC Lighter Mod

    The metal cover on top needs to be filed or grinded out so the atty will fit with extra room. it is u shaped and you will need to cut it all way to the sides so there no top part left, then sand with fine sandpaper. The red gas botton needs to be cut just in front of where the mounts to the...
  7. squeeze

    How to bulid a BiC Lighter Mod

    Once you get the batteries to fit in the lighter then you can start to mod the parts. The batteries. I used two 10440 350mah with no tabs, Hot glued them together side by side do not use a lot of glue on one side so you have room for the ground wire to come up the middle of the batteries to the...
  8. squeeze

    HELP adding pic

    How do i add a pic from my computer to one of my posts on my thread.
  9. squeeze

    How to bulid a BiC Lighter Mod

    Start with an empty lighter, Take off the metal top of lighter and then the flint wheel pry out the gas button, pull out the brass gas valve on the top. On the bottom of the lighter (the white part ) with a 3/16 drill bit drill three holes start in middle then the sides. Use a hot knife to cut...
  10. squeeze

    How to bulid a BiC Lighter Mod

    First of all please do not post to this thread till i am done!!!........ I would like to say that the batteries do fit tight in the lighter and you will need to take off flint wheel to push them out of the lighter from the top when they go bad. And the little tach switch does not hold up well it...
  11. squeeze

    Wooden Pipe mod Vote

    The wood work took three and a half hours to make that pipe. It's made out of paint mixing sticks i have made a few other boxes and thing from paint sticks before so that was easy to make.
  12. squeeze

    BiC lighter mod & parts

    Kind of hard to say I never used just the bic all day. But two 10440 batteries in parallel 700mah should last a little longer then and eGo650mah battery.
  13. squeeze

    BiC lighter mod & parts

    You could do that but you would have to grined off some of the lip on the atty connector to make it fit down inside the lighter.
  14. squeeze

    PTR08100W Mod Box

    Thank for all the info o4_srt I did't know that when the li-lon batteries get unbalanced they can dead short and explode/burn. And to buy a good balancing/charger rewire my mod, Its not worth it, I am just going to get two 14500 batteries and a charger. Take out the batteries and charge them...
  15. squeeze

    PTR08100W Mod Box

    Ok so you say my charge is no good, I did test it when charging the batteries in series with a volt meter on it and it did stop charging so i know the circuit protection is working. But like you said i can't relying on only that to be safe. I want it to be safe and you know a lot more about this...
  16. squeeze

    BiC lighter mod & parts

    It was not too frustrating to build, but having a hot knife to cut out the inside is a must. There is a post on my BiC lighter under experments with equipment that tells about it. On the charger it was a RN 4081 i took an atty apart to make the extension and soldered it on the charger then some...
  17. squeeze

    Wooden Pipe mod Vote

    I made this pipe but don't know how i want to set it up. Iam asking you all to vote on how i should set it up. 1. eGo mega atty /or 510 atty. 2. two 320mah batteries at 3.7volts/or make it a USB powered with a TI PTR-08100w regulator in it so i can run it at highter volts. 3. make the bowl...
  18. squeeze

    BiC lighter mod & parts

    3.7V two 320mah batteries with 510 atty yes it is real! here are some pics of moded parts if anyone wants to make one. And the mod charger.
  19. squeeze

    PTR08100W Mod Box

    I am relying on the protection circuit of the batteries from over load charging and yes charging in series. Good thing is used cell phone batteries at the goodwill for 1 dollar thats why i am using them.
  20. squeeze

    PTR08100W Mod Box

    Yes it has two batteries in series i took a board out of a 7.2V transformer hooked it up to a 9V transformer (see pic above)that got me down to 10.98V added two diodes and got 10.34V tested it under load and got 7.9V wow! so i knew i could charge in series. I made the charger first so i knew i...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu