Search results

  1. godspeed1208

    Where to buy 400 SS Mesh in sg?

    I was asking for places that sell in SG, if any
  2. godspeed1208

    Where to buy 400 SS Mesh in sg?

    Hi does anyone know where i can get the SS #400 mesh here in sg? I bought one and it does not oxidize even after doing it for like 10 times and i am out of mesh . Thanks
  3. godspeed1208

    Orion V2 roll call

    Ok thank you... I was just about to give up but you saved the day for me :toast:
  4. godspeed1208

    Orion V2 roll call

    i'm using the 32 a1 kanthal and 4/5 wrap... Should i lower it? i get about 2.9 and minus 0.8( when just putting the 2 probes together) is 2.1 ohm?
  5. godspeed1208

    Orion V2 roll call

    finally i realise what my problem was... like you mentioned it was not oxidized properly and i had to do it longer than i was doing it to get it oxidized, now my ohm is reading 2.9 with a 4 wrap is that fine oh should i lower it? Thanks alot for all the help.. finally i could get a decent vape...
  6. godspeed1208

    Orion V2 roll call

    oh ok thanks i think i understand now... i'll try to oxidized my wick once again and see what happens ;)
  7. godspeed1208

    Orion V2 roll call

    i place the probes on the wick and the numbers just keep running up and down anywhere from 10.2-30?
  8. godspeed1208

    Orion V2 roll call

    wick reads at 2.4 ohm resistence- minus that from 0.8 would be 1.6?
  9. godspeed1208

    Orion V2 roll call

    i cannot seem to get the hot spot to go away, from yesterday i've been trying to recoil and use new wicks as well but just does not seem to go away. Could the switch got spoilt? i just keep getting the burnt taste...
  10. godspeed1208

    Orion V2 roll call

    Oh ok didn't see that post, thanks alot . ;)
  11. godspeed1208

    Orion V2 roll call

    So should i take out the battery and where do i put the needles to check my ohm resistence? red goes to the negative nut below and black goes to top nut above?
  12. godspeed1208

    Orion V2 roll call

    can someone teach me how to use this multimeter? i went and bought one just a while ago but it does not have any instructions and i don't know where to place them to get a reading the coil/ohm readings. All i know is that the black wire goes to the COM hole.Don't even know where to put the red...
  13. godspeed1208

    Orion V2 roll call

    Nope, it was loose. but i have tighten it now. No hot spots for now ;)
  14. godspeed1208

    Orion V2 roll call

    it still has the hot spots... :(
  15. godspeed1208

    Orion V2 roll call

    yes i will be getting it soon after what i'm going thru now... I spoke too soon earlier. Till now i keep getting a hot spot at the top of the coil and it breaks/pops . i have done this about 10 times now and about to give up soon... something is just not right but i'm not sure what it is...
  16. godspeed1208

    Orion V2 roll call

    Ok i tried the old mesh i have left just enough to make my last piece... it's working now ... the new mesh does not work . I really don't understand why it did not work... i have to wait another 2 weeks if i were to order again..
  17. godspeed1208

    Orion V2 roll call

    I dont have a multimeter with me now, Now i wished i had one. Could something be wrong with the mesh?
  18. godspeed1208

    Orion V2 roll call

    i think so too.. when i try to fire it without a wick it glows evenly, so i was thinking the same thing, but i have pre-oxidize the mesh 3 times, each time soaking into water, and 3 times with my juice. I have done this before but today i'm not able to do it. i am using a new mesh i ordered from...
  19. godspeed1208

    Orion V2 roll call

    I've been trying to recoil with a new ss mesh and everytime, the coil breaks when the only the top coils lits up. What could be wrong? i have been trying for 2 hours now... i have pre-oxidize the mesh. i tried both twisted and single coils. 32 a1 kanthal and nichrome. And i need to get a vape...
  20. godspeed1208

    The iHybrid APV - A fully Customizable Genesis

    thanks ATX ;)
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu