Search results
-
Official Squape R[eloaded] thread!
Well it still leaks.. ;( less gurgling, vapable.. But still leaks.. That was when I left about 20% juice inside and left alone for an hour or so. I guess if I had continue to vape til dry it would be better? Not sure.. It was literally pouring out the air hole.. And the base was wet wet wet... -
-
Official Squape R[eloaded] thread!
Yesterday was my 1st B deck day. Vapes well for the 2/3 tank, then started gurgling/leaking badly. Few things.. Noted the nickel kinda sags lower, could be bcos it is too soft(30g) to hold the over saturated wick.. Also the set wattage was at 20w, only hitting just over 300F.. Increased to... -
Juice well of RDA
For me there seems to be a optimum amount of juice for vaping.. If I over drip/saturate it won't vape well.. Need to vape off the liquid inside a fair bit b4 it taste good.. -
-
-
DNA40 vs SX350j
this 'refinement' process... is it good or bad? I understand that the resistance of nickel does change over time, could be due to gunk or heat.. the SX 'locks in' the resistance for the atty, and stays at the setting until user decides to reset again. I've read about users using the same coil... -
SXmini M Class (TEMP CONTROL)
Yup happened once here also.. Reset and back to normal.. No big issue at all -
Official Squape R[eloaded] thread!
The SqR works fine with nickel.. So far I think most issues is with the KF4, probably too many parts connections to mess with the resistance reading.. But the gold plated spring seems to solve the problem. Anyway with dna40 and nickel I try to build above 0.1 ohms.. 0.15 if possible. Seems to... -
Official Squape R[eloaded] thread!
Hi Hey thanx.. I think my coil is set too low.. Pulled up till half the coil is showing, and now it's way better! Thanx again ;) -
-
VaporFlask Squonker!
Hi Well I just email him Abt the sx340j.. Hope the pricing is wallet friendly.. :) It seems from the pics you need to remove the screws just to change batteries?!- chia
- Post #78
- Forum: Liquid Feed APV Discussion
-
VaporFlask Squonker!
Hi You mentioned the Tmod customs.. Mech?- chia
- Post #76
- Forum: Liquid Feed APV Discussion
-
-
SXmini M Class (TEMP CONTROL)
Rubber mallet? I did take apart the gt2 to chk the wicking, and it's quite wet so most likely it's the 510 connector? -
SXmini M Class (TEMP CONTROL)
Hi Using a GT2.. At 0.07 build at around 20J.. Everything is fine initially, sync ok vapes fine, but sometime I get a 'dry coil' , even though the tank is half or full.. Sometimes I remove the batt and it resets and vapes fine, sometimes it persist.. Anyone had this problem b4? I suspect it to... -
VaporFlask Squonker!
Chk out vapinart.. Seems like he's expecting some E7s... ;)- chia
- Post #67
- Forum: Liquid Feed APV Discussion
-
Official Squape R[eloaded] thread!
Hey thanx for the tip.. I tend to wick on the thin side, as I get dry hits if I stuff too much cotton.. Do you think the PG/VG mix have a part to play? My current juice is kind of runny.. I think it is higher PG.. -
VG/PG juice questions
so a balance is needed.. am I right to say a high PG might cause slight gurgling? -
Official Squape R[eloaded] thread!
hi guys.. had the SqR for a while now.. I notice I always gets gurgling and leaks nearing empty of the tank, like 20% left of juice.. is it normal?