Search results

  1. ericbnc

    Free e-Liquid Giveaway/Riddle Contest Mothers Milk WTA Read Post 1....

    This one was tough but the answer is clearly "breasts" - the 129 gave it away...
  2. ericbnc

    Don't blame China.

    Ouch - that probably hurt! I still wouldn't mind asking Lindsay Lohan for her opinion though... :tongue:
  3. ericbnc

    Don't blame China.

    This is getting a little silly. Want to know where the Chief of Cardiology at our local yet nationally recognized magnet hospital came from? Harvard Medical School and Vanderbilt University Medical Center by way of Shanghai Medical University. He was made in China. I think the smart play would...
  4. ericbnc

    Provari & KFL+

    When I run a 1.2 ohm coil I might lose some high end volts, but I don't think I am missing much - at 3.8 volts I am already at 12 watts which is plenty for me with a Kayfun style RBA. Also, my 18650 battery lasts longer compared to a 2.0 - 2.5 ohm set up running higher volts.
  5. ericbnc

    Don't blame China.

    I remember when Al Gore and I sat down and invented the first e-cig. We invented Hon Lik and China too. Almost invented the penguin - our version could fly but it never really took off.
  6. ericbnc

    Water in lung?

    Don't vape while swimming or snorkeling and you will be fine.
  7. ericbnc

    Provari & KFL+

    My current KFL clone build is 1.2 ohm with 30 gauge Kanthal with the Provari set to 3.8 volts. This seems to be working OK for me.
  8. ericbnc

    ProVari - why the animosity towards it?

    I have some mech mods and some VV/VW mods. I can vape with more power than my Provari can output on all of my mech's and one of my regulated mods (The Duke). I still use one of my Provari mods when I am out and about though since it fits in my lanyard and gives me acceptable power for my out and...
  9. ericbnc

    Kayfun 3.1 emergency

    I gutted a dead laptop hard drive a while back - the screws worked on my KFL clone - might work for you if you have some dead electronics laying around.
  10. ericbnc

    Venders with quick shipping?

    Fasttech has the word "fast" in the name... :D
  11. ericbnc

    Replacement screws for RBA's

    The drive was made by Hitachi 2.5 500 mb SATA II 2.5"
  12. ericbnc

    Replacement screws for RBA's

    I swapped the hard drive in a friend's laptop recently. I kept the dead drive but didn't really pay it any attention. I was about to trash it but decided to gut it first. Many of the little screws match up with the threading for my RBA posts. Hope this helps someone source some quality screws...
  13. ericbnc

    Calling BS on dual coils!

    I built one of these in my Octopus dripper with two cotton wicks (Google bunny rabbit build or something like that). I used 30g Kanthal and it came in at 2.7 ohms but hits nice at 5.6 volts on the Provari.
  14. ericbnc

    Mech Clone under 60$

    This is the main problem for me too. If the shaft attached to the button has play the button wobbles when firing. The shaft needs support at the bottom (most mods are OK here) and at the top (few have this). I added a washer to my Origin clone button to give the button shaft upper and lower...
  15. ericbnc

    Level with me- Kayfun Lite + worth the dough?

    Another Tobeco fan here - from FT even - works great if the coil and wick are right, just like the genuine KFL+
  16. ericbnc

    Mothers Milk WTA Game Read post 1. Premium E-Juice giveaway.

    Congrats on the win but the molecular mass of nornicotine is 148.205 Nornicotine
  17. ericbnc

    The Brass Origin Clone From Fasttech

    I ran some test numbers to see how the mod performs. I used a 30 amp MNKE battery that reads at 3.97 volts. Without an atomizer the mod reads at 3.97 volts too. With a 2.2 ohm atty the volt drop is 0.06, and with a 0.9 ohm atty the volt drop is 0.13. These numbers are good enough for me...
  18. ericbnc

    Airflow/Draw Issues with My Russian 91 Clone

    How far in does the needle go - just a little bit or in almost half way through the base? I had this problem with a KFL+ clone too. I took a diamond needle grinder set (Harbor Freight)and went to work on the air hole. after a couple minutes of hand turning the bit sank into the hole - looks...
  19. ericbnc

    The Brass Origin Clone From Fasttech

    Another shot - no flash
  20. ericbnc

    The Brass Origin Clone From Fasttech

    I don't see much said about this mod - it's a sleeper I guess. Mine cost $19, so I wasn't expecting much. It hits good, has buttery threads as well as a decent magnetic switch, and works good out of the box. I modified my switch by adding a washer between the copper (plated?) bottom pin and...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu