Search results

  1. State O' Flux

    Is this a good battery?

    Mooch hasn't tested it... and it doesn't exist until he does.
  2. State O' Flux

    Best battery list below

    https://www.e-cigarette-forum.com/forum/xfa-blog-category/cell-tests.357/view-entries
  3. State O' Flux

    Is there a beginner's guide to mechmods?

    A hybrid mech doesn't have a general purpose, one-size-fit's-most 510 top cap... but rather a "floating" (at least as far as the tube threads allow) top cap with no independent 510, telescopic positive post set. The atomizer post is in direct contact with the battery positive... where clearance...
  4. State O' Flux

    RDA RDA on Cool Fire IV?

    Click on my avatar and go to my blogs... all my articles are there. Depends on what you think is important... and what's just bein' fancy. I'm a flavor vapist who seldom goes below 0.3Ω. I use Sandvik Kanthal A-1, direct from Temco in gauges 22 through 28. My most commonly used gauges are 24...
  5. State O' Flux

    RDA RDA on Cool Fire IV?

    Yep, yep... yep. :thumbs:
  6. State O' Flux

    Old Vaper New to Mechs - And my Mechs just arrived

    With unregulated mechs, you also must take into consideration, an "optimized" build for the wattage provided... per Ohm's law. For example... lets take the Ohm's law value for 0.4Ω @ 4.2 volts. 10.5 amps insures that you are well within the battery amperage potential, but other than the desired...
  7. State O' Flux

    RDA RDA on Cool Fire IV?

    At 0.3Ω... as long as you're using 24 gauge or thinner for a dual parallel coil, or 20 gauge or thinner for a single coil -- you'll be able to run a broad range of "heat flux" (perceived "temperature" of the vapor) from mid 100 mW/mm² to well over 400 mW/mm². Click the first (and second, if you...
  8. State O' Flux

    Is there a beginner's guide to mechmods?

    With unregulated mods, your wattage output is determined by battery voltage and the atomizers net resistance... this value is calculated using Ohm's law formulas. Atomizer builds must be optimized, primarily for wire gauge and coil count in parallel... to obtain a desirable balance of...
  9. State O' Flux

    RDA I'm so confused - single and dual coil

    You may need to "up the wattage" a bit more. Going from a single coil to dual parallel coils with no other adjustments makes for a very "cold" vape. I'll provide examples... and this is reverent, in varying degrees, regardless of your actual resistance and wattage. This is a 1.0Ω single coil...
  10. State O' Flux

    Help - Steam Engine And Real Life Coil Specs Don't Match

    When ever I run into a discrepancy with SE calcualted net resistance vs. what an actual or anticipated value is... it's usually the wire actual thickness vs. the SE "standard" gauge thickness. It's most frequently thinner than the listed value, but I've run into a few that were thicker. In...
  11. State O' Flux

    mandrel set

    Sure. Pop onto FT, enter "Coil Jigs" into the search engine and ta da! All the fixtures, and mm marked mandrels you can eat.
  12. State O' Flux

    ModWorx 38A 2100mAh 18650 Bench Test Results...only a 20A battery, collapses at 38A

    And another one bites the dust. Mountebanks? All the way back to the early 19th century... had to dig deep for that one, didn't ya' sonic. :thumbs:
  13. State O' Flux

    Juice not flowing up to the coil.

    Nothing in the above really stands out as a possible issue. You've left out a few things, so might still be in that info... or perhaps you inadvertently fixed the issue by changing builds.
  14. State O' Flux

    Juice not flowing up to the coil.

    Specifics help. Off the top of my head... Device used and wattage setting. Build type, incl. wire gauge and coil ID. Net or measured resistance. Relative position of coil(s) to juice well. Juice PG/VG blend. Atomizer brand and/or model. Wick material, brand or type. Wick density. (compression...
  15. State O' Flux

    Need advice on this coil build

    https://www.e-cigarette-forum.com/forum/blog-entry/the-practical-applications-of-heat-flux-wire-gauge-parallel-wire-count-net-resistance.7308/
  16. State O' Flux

    Charging Time on VTC4s in Intellicharge i2

    You don't have to wait until you've got a full, 4.2V charge, but... I'd wait until you have at least the 3.7V nominal voltage.
  17. State O' Flux

    RDA Shorting problem with Poseidon Shorting Help

    Check the atty positive post. Is the post head (510 positive) being pushed, laterally, into, and making contact with the atty body (510 negative)... when screwed and snugged into the mod? I've seen a few clone Poseidon V3s where the positive post head is only a few thousands smaller OD than the...
  18. State O' Flux

    Battery Safety. (Help Needed!)

    https://www.e-cigarette-forum.com/forum/blog-entry/18650-safety-grades-picking-a-safe-battery-to-vape-with.7447/
  19. State O' Flux

    RTA/RDA Power Ratings

    You use terms "power" and "structure", as seemingly interchangeable elements... neither of which are specific. The true limiting elements will be heat, air pressure/vacuum, and chemical in nature. RDAs don't necessarily have a resistance "lower limit"... other than temperature effects on what...
  20. State O' Flux

    Steam Engine and Clapton Coils

    Chances are, Lars will be dumbing it down... for even denser melons, like mine. o_O
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu