Search results

  1. J

    Just For LM2596 Users

    go go go :D, I wait to see what you make :D
  2. J

    Just For LM2596 Users

    @Quigsworth what is the status of your project with lm2596 and digital potentiometer? :D
  3. J

    Touch switch question...

    Belive me..A single batt`s connected to atty it`s not like booster, have drop down voltage on that mosfet, with atty connected. To minimize this dropout voltage need to use a mosfet with lower VGSthreshold, in that way the mosfet will be totaly open in load.
  4. J

    Touch switch question...

    you may use from mosfet with VGSthreshold = 0.4 ..1V for mod 3.7V batt`s- switch -atty.this IRLU3114ZPBF it`s good only to pull down a on/off pin from an stepdown IC
  5. J

    LT1370 boost converter?

    i try to experiment some booster with this IC, it`s not works. Try ltc3872..good booster, much better than lavatube.
  6. J

    "The Eraser" VV ori noVV mod

    thank`s :)
  7. J

    Boosted vs Regulated

    regulated dual batt`s series connected it`s the best.Huge power, long life of batt`s between recharging..but dimension is a little higher of this kind of mod, compared with booster.
  8. J

    "The Eraser" VV ori noVV mod

    ..and image. You can contact PM or jhonutz33@gmail.com
  9. J

    building in charging

    yes you can. Use 14500 protected batt`s anyway.
  10. J

    Stupid question #326...3 wire meters

    it`s works but i don`t know what current drain from batt`s in stand buy, probably not much.
  11. J

    Are All Watts the same when vaping

    i don`t agree with that. only problem is user..want to have hard sensation but instead take some burned taste...VV it`s good but you may use correctly.I say in other posts..must find the "sweet spot" wright voltage at a fixed resistance.
  12. J

    Are All Watts the same when vaping

    for this it`s much better to use kanthal.
  13. J

    Are All Watts the same when vaping

    to change this watt`s on out you have two way. Or use lower resistance or increase voltage.
  14. J

    PTN04050 Booster, need help! (Since i succed with the PTR08100 next...)

    welcome.Anytime i help you.Let me know if you succeed..
  15. J

    modified imist

    thank`s :)
  16. J

    PTN04050 Booster, need help! (Since i succed with the PTR08100 next...)

    for a booster it`s normal to have drop down voltage, but it`s major under 2 ohm carto/atty. Maybe other will help you, i don`t have any solution.
  17. J

    PTN04050 Booster, need help! (Since i succed with the PTR08100 next...)

    from adj pin you need to put a resistor divider, one to + and outher (potentiometer) to ground.
  18. J

    PTN04050 Booster, need help! (Since i succed with the PTR08100 next...)

    need at least 100uF to IN and 220 uF to OUT, try to put higher value on out.
  19. J

    PTN04050 Booster, need help! (Since i succed with the PTR08100 next...)

    this noise is from switching. however a booster work with 1.9 ohm.Seems you make something wrong :glare:
  20. J

    "The Eraser" VV ori noVV mod

    i just finish one like the first four pictures.It`s VV works with 2x16340 only,varivolt from 0 to 8.4V, sensitive switch.Have revers polarity protection, short circuit protection, thermal protection I sell this for 140$ without batt`s, priority shipped included (with tracking...
Top Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu